I'm trying to design a very low power sensor that takes readings using ADC and SPI 200 times a second. I'm a bit worried by the current EasyDMA uses (1.1mA). As far as I can...
Hi, I am working on a project where I want to make one nrf51288 chip as central hub and connect that to a android phone and other salve nrf51288 .
idea similar to this: ...
Hi,
I have a code programming the nRF51422 development board to write to a Sharp Memory 96x96 pixel LCD screen using SPI.
Currently the code writes two numbers and a...
I've modified the ble_app_uart example by adding GPIOTE so that the transmitter sends a character to the receiver when a GPIO pin is toggled. This part is working well.
...
Hi,
I am working on my hardware product having nRF-51422 chipset. I just came to know from forum post that
nRF-52 chips will get arduino IDE support as standalone. I want...
Hi!
I've been using PCA10028 for a long time and I had some bricking issues but I've managed to un-brick it with "nrfjprog --recover" and everything would work again. ...
I want to build nrftoolbox app in android studio. I downloaded the zip file from the github website and also the required dfu library. I unzipped both the files in a folder...
8Q BTLE issue.pcapng BTLE connection failure.log
Hi guys,
We have an issue with some iOS devices that are disconnecting with reason 0x08, the connection timed out. The...
I have used NRF52840 and SDK 13.0.0. Module SPIM.
Nrf driver does not support frequency more then 8 MHz(enum does not have constants for 16MHz and for 32MHz).
But I have...
Hi,
I tried to use fstorage to store some data in flash.
From now, I was able to read and write data before advertising starts, but when I try to write data to flash after...
Hi,
I am currently trying to perform DFU update over BLE, I am working on SDK v11.0, and Softdevice S130 v2.0.0. My traget is an nRF51822-QFACA1.
When I enter in bootloader...
Hello everybody,
I'm designing an app to track the position of the smartphone using six beacons and, in order to do that, I made some measures both indoors and outdoors...
Is there any example combining the Serial and Over the Air DFU for the SDK13?
Or the posiblity to combining the two features into a single bootloader?
What steps should...
Iprogram the bootloader.hex to 0x78000 with jlink.Then in my application program,I set the NRF_UICR->NRFFW[0] register as belew:
static void write_uicr_customer_register...
When power on,run app first at 0x1f000,then reset and run to boot loader at 0x78000,how to set UICR registers to make this come true?I try to set the NRF_UICR->NRFFW[0] in...
Hello,
I want to build a system which will use 2 nrf8001 to communicate. 1 nrf8001 will act as a client by continuously transmitting its UUID and another one will act as...
I am working on RTLS project. I want to perform DFU in beacons but not getting proper information .I went through ( devzone.nordicsemi.com/.../) but i think it i for SDK 13...
I have a hex string like this 58FF1CE5.This is corresponding to One date time 16/09/1955 .(ie in MM/dd/yyyy).How can i do this in ObjectiveC, I am getting this date in didDiscovercharacterstivc...
After some search I found that accepted values for tx power are -40, -30, -20, -16, -12, -8, -4, 0, and 4 dBm.
So my questions are
once I set the tx power using ...
I will code 1 to 2, however, was not successful
code1 :
u8 IICwriteBytes(u8 dev, u8 reg, u8 length, u8* data){
u8 count = 0;
IIC_Start();
IIC_Send_Byte(dev);...
Hello Nordic Team,
I would like to know if it is possible to do a DFU of my SDK10 based application ( s130_nrf51_1.0.0_softdevice + SDK10 Bootloader ) on an nRF51822 (32...
