the proximity example is running ok. but when I modify the length of the alert_level I have the following error on the server side that I am not understanding.
476;16:12...
Hi all,
I'm working with the nrf51422 and the nrf51822 and I was wondering what the current status of the over the air DFU system is.
I'm using SDK 6.0 and I managed...
nRF24l01+ at a transmitter module one time successful transmission show & after 1 sec failed also . if any doing programming with atmega32 ,please send code for TX & RX ....
Hello,
can the radio notification and radio disable APIs be used to use the radio hardware from the application layer?
Background of my question is, that I have an application...
Hi,
I am using central s120 with peripheral s110. The connection to the peripheral is depending on the name advertised by the peripheral.
When connection is done, the...
Hello,
I am trying to ecrypt some data in order to send some data encrypted in the MINOR and MAJOR adverts of the device.
I used this code to ecrypt the data ( this is...
Hi,
i use anRF51822 with soft device 7.
I run the UART app on my iPhone 4s with ios7 and on the nrf51822 board the ble_app_uart with keil uVision5.
Both devices connected...
Do nRF8001 chip has its own internal linear regulator? or Does it need an external like the module created by Adafruit ( https://cdn-learn.adafruit.com/assets/assets/000/035...
Good evening all,
I'm trying to get my DK52 communicating with a CR95HF (this is a NFC controller with serial and SPI control interfaces), I'm using a breakout board - BM019...
Hi Sir, I use load switch circuit to control nrf8001's power. I found even the vcc of nrf8001 is empty, nrf8001 still works. That's not my expected result, I think nrf8001...
Hi ,
We know that the nRF8001 use the random static device address . I have the questions below :
A. Will the device get one new address after power on ? or is the address...
Hi,
I need to exchange data between 2 ble modules.
I'm using SKD 15.0.0 and first ble module is nRF52840, second ble module (esp32) acts as GATT server.
I have full...
Hi, I am trying to make nrf52832 as a UART certal. The service UUID and characteristic UUID of peripheral are shown as the following picture. They are all 128bit and quite...
I'm attempting to implement a simple, GPIO driven interrupt system using SDK15, but I can't seem to find any examples using the nrfx_gpiote driver, or documentation on how...
I am currently working on a master thesis at NTNU, and are working on a sensor system based on audio collection and classification (Machine Learning). Power consumption is...
Hi Support engineer,
I am quite new to Nodicsemi devices, I am going through some getting started tutorials, but I found there is no tutorial based on Segger Embedded Studio...
Hello,
I'm usign nRF52832 with nRF5_SDK v15. I'm using "ble_app_uart" example. I need to know that What is the maximum datarate for "ble_app_uart" example ?
In the...
I have a question with flash writing of nRF 52. Once written, you can not write it for the second time. It will not cause an error, but is there any way? Write the source...
Runtime environment:
1.IC:52840QIAA ；
2.SOFTDEVICE:s140_nrf52840_5.0.0-2.alpha_softdevice.hex
Development:
PWM signals of 10 groups of adjustable frequency and...
I am trying to establish communication using SPIM. when I checked the macro definition of NRFX_SPIM0_ENABLED it's present in apply_old_config.h. I am using nrfx_spim driver...
Hi,
I have two 52832 (both on SDK 14.2, S132 v5.1) talking to each other using a slightly modified UART service to support more than one connection.
I have this strange...
