I'm moving to 2.9.1 and trying to get mipi working with a st7789 display. I have it working with 2.6.1 without mipi, but can't seem to get it working with mipi on a nrf5340dk...
How do I produce a signed file to flash to the network core for firmware update? I am using a child image/parent concept with the \nrf\samples\ipc\ipc_service\ project, When...
Hi,
I’m working with the Wi-Fi station example on the nRF54H20 using SDK v3.0.0, and I’m encountering a critical issue when trying to bring up the nRF7002EK Wi-Fi module...
I have a project using BLE as a central on an nRF5340 to connect to several devices. For factory test I am being asked to implement something that can be used in the factory...
Dear Nordic Engineering Team,
I am currently developing a wireless ECG acquisition system based on the ADS1298 analog front end (AFE), the nRF5340 SoC, and the nRF7002 Wi...
Hi,
I believe 2M and 1M are OK to adjust, however, long range code added the extended advertisment, I am curious whether I can update these three PHY all together.
Thank...
Hi,
I was wondering if the newest sample available in NCS3.0.1 is already capable of holding multi connections. Otherwise, for this little time that is present i will...
Hi,
How is the functionality of P0.21 in nRF52832? It is configured as RESET after turning on the device, right? Is there any way to change it in a way that that the chip...
Hello DevZone,
I am using a nRF52840 for project development.
To test SPI setting is correct or not, I am doing the loop-back test, I set the MISO and MOSI PIN according...
Hello,
I try to configure two nrf52832 devices work with payload of 200 bytes (data should be 200 bytes, not the all ble packet).
I took ble_app_uart_c peripheral and...
Hi all,
Using UART is confusing for me because I see various implementations in the documentation. There is a Serial library, then there is the UART driver and HAL. The...
I am trying to use the comparator to wake me up when a potentiometer is moved a certain amount.
Before I sleep I read the ADC value of the comparator and use this to set...
Hi,
I'm trying to set up the connectable/scannable advertising. I took the app_beacon example and changed advertising parameters.
My final set up is:
The ADV_INTERVAl...
I have the preprocessor define CONFIG_NFCT_PINS_AS_GPIOS in my code, and GPIO functionality for P0.09 and P0.10 are working just fine for me...
My issue is that even when...
Hello!
I'm a beginner with Nordic products and I'm taking over the nRF52840 Preview Development Kit.
I want to send advertisings at regular intervals (every second...
Hi,
Is it possible for an 3 party BLE device like an mobile device like an Android/IOS Phones or ESP etc to participate in mesh notwork if so is there any documentation...
I have been unable to perform a DFU over BLE using the bootloader_secure_ble example.
I am using SDK 14.0, nRF52832, S132 with a custom board, along with the nRF51 Development...
Hello,
I want to factory pair nRF52 to nRF52 connections (NUS) with a factory set key but i'am lost.
I digged in NFC pairing but it's too complicated for my understanding...
Hello,
i use IAR EWARM 8.20.2 and SDK 12.3.
I compiled the blank Blinky example from the SKD for the pca10040 without any Errors or Warnings. When i load the .hex to the...
I use IAR EWARM 8.20.2 and the SDK 12.3 because i want to use the S130 for the nRF51.
I installed the provided MDK_8_11_1_IAR and now there are two options for Nordic Semiconductor...
