Hello everyone,
I am using the great platformio toolchain that supports the mbed framework so far. I am still a newbie to it however.
I want to be able to use both the...
Hello!
I have a device with nRF51288. And I need to fill technical specification with the following parametres: operation freq., channel bandwidth, modulation, number of...
Hello,
Does anyone have a suggestion for a production programmer for the nRF24LE1 One Time Programmable version? I have been able to program the units with the nRFGo Studio...
GOAL: To send one 20-byte data packet from an Android Galaxy S5 to nrf51822 and send three 20-byte packets from the nrf51822 to the S5 in a single connection interval of 10...
Hello, I have looked into the compatibility matrix and I couldn't find any clear answer about if the NRF Beacon Kit is compatible or not with the S130. Does anyone tried to...
hi:
now.i have a development board(nrfgo motherboard).there is a debug port on the board.i think it can be debugged on the keil.if it can.what driver or others i need.thank...
This is what I got after upgrading my nRF51 dongle firmware.
It always times out.
I didn't somehow got one of my J-Link Lite upgraded, but couldn't repeat the process...
[nRF5_SDK_15.0.0_a53641a] is used. Please tell me how to select peripheral when connecting from central to peripheral. Since I want to connect to 4 peripherals for one central...
Hi to all,
i am developing a device with nrf51822 soc and i want use it as peripheral, in it have a characteristic that i want read it continuously from central. sometime...
I am using Hackable kit which is a custom nrf52832 board with Bumpy a low cost Black Magic Probe alternative to program since i don't have a J-Link device. I have tried many...
Actually, I am working on a IoT project in which tens of connectionless BLE beacons are broadcasting packets. Now, four Nordic devices(nRF52832) are receiving that data and...
I want to use the 2450AT42E010B chip antenna from Johanson Technology in my design. I selected this antenna specifically because i want to make a beacon using the nRF52832...
I want to build a device able to connect with smartphones and central modules preinstalled on the ecosystem.
Is possible to integrate Bluetooth mesh + Peripheral role in...
I have the nrf51 RADIO peripheral set up with the usual set of shortcuts:
NRF_RADIO->SHORTS = RADIO_SHORTS_READY_START_Msk | RADIO_SHORTS_END_DISABLE_Msk | RADIO_SHORTS_DISABLED_RXEN_Msk;...
Hi,
I'd like to be able to use an event from the LPCOMP to sample the RTC (either to a peripheral's register, or to a memory address), so I can measure pulse widths without...
I am able to initialize the module and get the callback , but when I try to write I will not get the callback after the write, and no errors.
If I simply try to read after...
Hi
I am integrating BLE with LESC into a legacy sensor product using SDK v11.
The problem I am running into are errors in the FDS module when trying to make a secure connection...
I use nrf52832 based on SDK14.2 as a slave development. Occasionally there will be a crash in the operation. The program has been running in the “params_reply_pending_process...
Hi Nordic Community
I'm doing a risk assessment, and I couldn't find a proper answer for the fallowing two question, it would be great if I could have your opinion and...
I am trying to set up the sniffer on nRF52832 DK PCA10040. I am not seeing the COM port on the Wireshark interface. I can see it on the device manager. I have looked at other...
Hi Everyone , I am using SDK v15.0 for nrf52840 with segger embedded studio.
I tried the example code given for blink freertos. I am able to run two tasks but as soon as...