I am working with NRF52840 with SoftDevice S140 and SDK v17.1.0.
The boot loader address for this chip is 0xF8000. I can set up one of the 'fstorage' module with the address...
Hey everyone,
Does anyone here have experience with firmware OTA updates over the JIO NB-IoT network? The process seems a bit different since JIO Cloud always sits between...
Hello:
The latest nRF54L15 Errata for Rev 2 shows that the previously reported "GPIOs can exhibit radiated emissions" is no longer present in the Rev 2 SoC.
Can you please...
Hi, this is a very broad issue that i am having, because i dont know the source of it. I am simply unable to use the bme68x IAQ library. i have downloaded the external bsec...
Greetings!
I am using Wireshark along with an nRF52840 dongle to monitor BLE traffic between a mobile app and connected peripheral and periodically I see some "L2CAP Fragment...
Hello, I am using the nRF54L15 board, and trying to connect to the Adafruit SHARP 400x240 monochrome LCD display .
I got the display driver alone to function just fine after...
Hi,
I am trying to perform a DFU using SMP over BLE. My setup has NSIB and MCUBoot enabled and thus I am able to perform DFU for MCUboot and Application using nrf device...
Hi everyone!!
I've gotten the ipv6_coap_server example to run on the nRF51-DK,and I use raspberry pi as gateway and I can got the bt0 interface after connecting to the...
I would like to add LIN-bus to a project of mine.
The hardware part is easy, connect a LIN interface ASIC to the UART of the nRF5x.
But writing my own LIN-bus SW driver...
Hello World!
I am trying to interface an LCD with nrf51-DK. I basically need to send 3 signals - SCLK, MOSI and SS to the LCD. I have modified the spi_master example from...
I am working with a sensor which has a programmable configuration register. After changing this register, I have to reboot the sensor. To do this, I need to temporarily suspend...
Hi, I try to send data through SPIM to my panel(Sharp Memory LCM), and I success get the picture (only part of the picture).
The reason why is that function can only...
I have migrated to SDK 9.0 primarily to take advantage of some of the Advertising Mode functionality in Device Manager. While I was still in SDK 8.1, I had implemented functionality...
When you download win driver (from www.nordicsemi.com/.../72324929 for instance). There's only a win32 dll/lib provided.
However, modern development are often made on 64bits...
I am using nrf51822 with s110 softdevice. My goal is to allow pairing and bonding to a single central device. Once its paired and bonded, it should not allow connection and...
In one of our projects the nrf51 shares the SPI to a device with an STM32 microchip. To be able to successfully share the SPI channel, I'd have to put the SPI pins of the...
Hi,
I am currently using nRF5_SDK version 11.0.0.
I have 2 nRF52832 development kits.
On the soft device side, i am using S132.
My understanding is that this (S132...
I want to make a blinky program from scratch and have no idea how to settup keil. I would prefer something step-by-step. I have been able to use the precompiled example, but...
Hi all!!!
I'm new in here.
I'm reading document with link: developer.nordicsemi.com/.../index.html
In Figure 1, I see a phare: "IoT Device". Is the "IoT Device" nRF5x...
Hello,
my setup is nrf51822, with SDK 10.
I try to create application to drive I2C components and I get compilations errors:
In function 'Hal_I2cInit':
../../../nrf5...
