I'm trying to implement a fall detection feature on the headset side using the LSM6DSOX IMU sensor. The IMU is configured successfully, but the board halts after the INT1...
Hello Nordic Team
I am using SDK 3.0.1 with a nRF52DK to develop a firmware that can be switched from BLE mode to GAZELL mode and vice versa over a command sent via UART...
Hey everyone,
Does anyone here have experience with firmware OTA updates over the JIO NB-IoT network? The process seems a bit different since JIO Cloud always sits between...
Greetings!
I am using Wireshark along with an nRF52840 dongle to monitor BLE traffic between a mobile app and connected peripheral and periodically I see some "L2CAP Fragment...
Hello, I am using the nRF54L15 board, and trying to connect to the Adafruit SHARP 400x240 monochrome LCD display .
I got the display driver alone to function just fine after...
Hi,
I am trying to perform a DFU using SMP over BLE. My setup has NSIB and MCUBoot enabled and thus I am able to perform DFU for MCUboot and Application using nrf device...
Hello,
I admit, that this is a bit of advertising for my open source mesh protocol, but I'm also curious if there is anybody that successfully compiled it and if there...
Hello,
I get an error fatal when running Heart rate collector example from SDK12 on PCA10040 development board.
The sensor use example from SDK15 on a nRF52840-DK.
Some...
Hi,
I want to use Segger Embedded Studio to write firmware for Thingy 52 but I don't know what programming hardware I need. Is there any documentation that supports Segger...
Hello,
Thank you for helping me to interface the Si7021 humidity and temperature sensor with Nordic nRF52 development kit board. I need to write the necessary code to finish...
Hi,
I am using nRF52832 for my development, I want to send 8 bit device ID as an advertising packet with company ID and Data.
Is thereany way to send the same or any example...
In earlier releases of the mfw for the nRF9160, we got 3 files with the image, one of them being firmware.update.image.hex. This is missing in the new updates. How do we update...
Hi, I have a PCA10000 nrf51 dongle, I use with wireshark and the nrf sniffer plugin. I followed all installation steps for the version 3 of the sniffer and the latest version...
Hey guys,
I'm working with a Laird BL652-DVK (nrF 52832 - chip), Nordic SDK v.14.2.0 and SES (Segger Embedded Studio v.4.30). My goal is to send datas from sensor (accelerometer...
hi
i use sdk12.3 (51822), i see only ble_app_hids_keyboard and ble_app_hids_mouse.
I want use mouse +kb device. I use ble_app_hids_mouse add kb function . then my android...
Dear All,
For a reason that I can't understand so far, I must erase the nRF52840 to be able to use UART1, TX RX on pins 0 1 (connector P14) to communicate with an external...
Hi,
Do you know which of the two version of ADP5360 the Thingy 91 uses?
is it
ADP5360ACBZ-1-R7 or
ADP5360ACBZ-2-R7
Both versions are available now at Analog's...
SDK: 15.3.0 Device: EYSHJNZWZ (nRF52832)
"nrfx_wdt_event_handler_t" can be set in "nrf_drv_wdt_init". After the "nrfx_wdt_event_handler_t" event occurs, the WDT is reset...
HI，
When I use NRF58240 to develop GPS positioning function, APP_UART_COMMUNICATION_ERROR appears, but when I do not connect the GPS module, there is no such error. What...
