I've been able to flash consistently but I finally got my nrf5340 custom board working using Hight Voltage DC/DC by setting it to UICR_VREGHVOUT_VREGHVOUT_3V0, but when I...
Hi,
I had a working project for nrf Connect NCS 3.0. I don't know what happened, but now I can't even create a new build configuration. Every time I click on "add build...
Hello,
Please forgive me for this question. I am an extreme noob. And am trying to get started with my first project.
I am working with the nRF52840 DK, and I am trying...
Hi,
I am trying to make the nrf52833 into an Auracast broadcast receiver (for a broadcast from my phone).
I am using bindings to the softdevice controller ( https://github...
Hi Nordic team,
I tried to view logs from my custom nRF54L15-based MCU using J-Link RTT Viewer, but it's (printk) not working. The same prj.conf configuration was previously...
Hello Nordic Support Team,
I am working on an nRF52-based project on a custom PCB using the E73-2G4M08S1C devboard ( https://www.cdebyte.com/products/E73-2G4M08S1C ).
...
NRF52840
S140
APP based on ble_app_multilink_central
1 PCA10056 as central, 1 PCA10056 as peripheral, the cantral can find the peripheral and buid connection.
But...
Is there somewhere that we can see the defconfig file for the Raspbian images generated here (under downloads): www.nordicsemi.com/.../nRF51-IoT-SDK
We'd like to integrate...
Hi, When using RBC mesh and SD8.0.0 I often get assertion at line 189 in soc_radio_timeslot.c.
This file is part of sd8.0.0 and I dont have source code. Why is this assert...
Hi all,
I am trying to send data(rssi+MAC address) from GATT server to GATT client using sd_ble_gatts_hvx(). I added the service and the characteristic into the ATT table...
Hi,
Following the AN 29 "nRF51 Development with GCC and Eclipse v1.1", I cannot import any project on Eclipse for nRF51822:
In step 1.2 "Import existing Eclipse project...
I work for a small start-up. Our products monitor events and communicate via bluetooth with an Android tablet.
We are currently trying to make our custom circuit using...
I'm using
s110_7.1
sdk 7.2
DFU
updating application (application.hex + application.dat zipped) works fine, but when updating bootloader (bootloader.hex+bootloader...
Hi,Nordic support
Circuit design: Unused I/O pins
where can i found recommended I/O end terminal desing of unusing GPIO pins ?
I'd need such as pull-down resistor......
HI, I'm extremely new about Nordic component and device.
I buy a nRF51 DK for start understand hou BLE work, I attach to my pc, the green led power on and my pc know the...
With S110 v8.0.0's size increased to 96K, I'm concerned that my current memory layout is going to prevent me from upgrading to a future softdevice.
It seems that the only...
The function dfu_ble_get_peer_data seems to be declared in dfu_ble_svc_internal.h
but not defined, (not actually implemented) somewhere deep within the Nordic Software Packs...
Folks,
Simple UART communication shouldn't be this difficult. Embarrassed to admit it, but I'm having problems setting up and using the app_uart.c/.h module from the SDK...
Hi all,
I have a working prototype of a service which enables a number of characteristics for the control of motors and relays. The motors work great, and are controlled...
Is it possible for gpiote_event_handler interrupt to get executed while the program is executing code inside timer_event_handler?
These events modify same variables so...
I intend to keep a long running clock in the system and use the app_timers(hence RTC1) in a soft device enabled nrf51822 firmware.
I basically have a minute tick and update...
Hi,
I want to run the experimental_ble_app_uart application on our custom nRF51822 board.
However, I could not find a proper bootloader to start the application. Is...
