Hi all,
I have an application where an nrf24le1 is communicating serially with another processor, using the UART at 57600 bps. I have multiple identical boards communicating...
after flash DFU program into pca10001 board, com3 is not accessible,
www.dropbox.com/.../Screenshot 2014-04-26 15.41.47.png
even after I erase all, and re upload soft...
Using S120 V 8.0.0.3 alpha, processing a BLE_GATTC_EVT_READ_RSP,
received 0x16 bytes of data but there is more to read. Next call to
sd_ble_gattc_read using the same connection...
Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
Hi Nordic Team,
Can you please share any information regarding Indoor Location Tracking feature/application that nRF52840 can support? does this have AoA/AoD? and can this...
I want to establish BLE connection and have a central device receive data from a peripheral device. I am using the Heart Rate Collector as an example and notice the main file...
Dear All :
Is it possible to creat a pwm with 1sec period?
Since the lowest frequency of the base clock is 125kHz，the top count of the pwm with 1sec period will be 125000...
Hi.
I havent found answer for - in my opinion - common question - how to temporarily change name of ble device on button press. As long as button isnt pressed - advertise...
Hi, I'd like to know if there is a way to subtract two different square waves that are coming from two different input pins and then measure the pulse width (or the frequency...
I have been using Power Profiler Kit nRF6707 for awhile without problem. If I made a mistake by downloading firmware when the PPK is attached to nRF52 DK, the software on...
I followed this tutorial in Infocenter and installed everything infocenter.nordicsemi.com/index.jsp , but I have a problem with Thread examples, programming output looks normally...
Hello,
I am working on nrf52840 EVB , i programmed the board BLE_APP_UART but this profile is not working , still the board functioning previously programmed blinky example...
I'm not sure exactly how to word that,
I am about to try and get the adafruit feather to consume less power in standby and I've been told the arduino library isn't well...
Hello,
I am using pca10028 and sdk 12. I want to use 2 uart for my application but as per datasheet nrf51 has only one hardware uart. Can I implement soft uart on pca10028...
Hi, I would like to measure the electricity consumed at my home(220-240V) with the nrf 51822 and send it over bluetooth. No problem on the bluetooth side, but how can I measure...
I have a buttonless device using a DFU bootloader and ble_dfu buttonless DFU service with SDK v13.0.0. I'd like to make the ble_dfu service available for 5 minutes on power...
Hi Sir,
I am using nordic nRF51822 IC for Tracking Application for that Which antenna is best ?
I have seen two type of antenna .
zig zag pcb antenna
straight...
Hi, Nordic Forum!
We have developed our own logging module backend so we can store logs in an external flash memory. But now we wanted to transmit those logs via BLE to...
