Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
SWI*_IRQ is using by softdevice to send event to application, I want to know which priority does softdevice set for them?
Does sd_nvic_critical_region_enter() disable...
I am a started guy.
I only need a bluetooth device (BLE) to check the signal and mac address.
What is the best choice?
I need the smallest and low powered!
Thank you...
How does the Tx power impact the scanning and connection with a peripheral?
In detail, say if the peripheral can advertise at a Tx power of 4, 0 or -4 dB, then will it...
Hello, dear Nordic employee,
MCU: 51822QFACA1
The using SDK is : SDK 7.2.0
The using SD is : s110_nrf51822_7.3.0_softdevice
There was one device (our product) runing...
Hi,
I am using "nrf5 sdk v11.0" example "ble_ancs_c" for nrf52_DK(PCA10040) .
when i connect to the nrf_device from ios device i am able to pair and connect to ancs client...
Hi,
I'm using the example nRF5_SDK_11/examples/ble_peripheral/ble_app_uart witn a pc10028 board. The central is done on a linux machine with a python program under bluepy...
Hi,
We would like to use the nRF52 in the following way:
BLE communication via S132
button / IRQ to wakeup nRF52 application
put nRF52 to sleep after BLE communication...
As we known,RSSI means Received Signal Strength Indicator,TXPOWER decide the power of output port.How do the two factors combine affect the device work?
Hi I spent a few days on trying to setup a thread external commissioner using Nordic nRF52840 and RaspPi 3 as a border router.
First I realized that border router implementation...
Hi
I'm having major problems implementing current time service client (cts_c). I've run ble_app_cts_c on my device and it works fine. I copied the relevant parts of the...
Bluetooth SIG recently released BLE Mesh standard 1.0. Is nordic mesh compatible with the new released SIG standard?
If not when is it planning to release a SIG compatible...
Hello,
I did used nrf_drv_spis.c (SDK SPI Slave) with nrf_drv_spi.c (SDK SPI Master). And I notice that both module configure SPI MISO line as input without any pull (neither...
Hello,
I am using nrf52832 DK and I would like to use the GPIOs port to debug a couple of signals that I genereate within the MCU.
So far I have configured my GPIOTE...
Dear experts,
I've been playing around with Thread since nRF5 SDK for Thread v0.8.0, cloud_coap_client.
I use your Border Router example with NCP example running on nRF52840_Preview_DevKit...
Hi:
I got an 0x04 no mem error with sd_ble_enable.
But my hardware worked just fine before, so after some tussle I found out that the sd_ble_enable of my working program...
how to set the ble stack ,let the sd_ble_gatts_hvx() send data return more fast,now from i use sd_ble_gatts_hvx() to get the return (BLE_TX_COMPLETE) needed 300ms.
