Hi,
I use two evk board to connected and test the uart serialization sample(ble_s110_serialization), one is ble_app_hrs and one is ble_app_connectivity. But I have one...
I am getting get BLE_EVT_USER_MEM_REQUEST and BLE_GAP_EVT_CONN_PARAM_UPDATE event, when writing to ble device, sample code did not handle these event, and seems no document...
Hello:
Why do I erase SDK5.2 version of flash and read not, in SDK4.2 can. I tested nrf51_sdk_v5_2_0_39364\nrf51822\Board\nrf6310\flashwrite_example is a good example.However...
before i write the flash, it has been erased.so ,its value is all 0xff.
when i write 0x00 to flash address 0x0001,the value read out is not 0x00 but 0x01,and the value in...
I'm looking for a way to use the nordic uart service ( devzone.nordicsemi.com/.../ble_sdk_app_nus_eval.html) from Linux using the native Linux BLE Stack (BlueZ). My application...
Hi,
I've created an application using the S110 experimental ANCS demo. I successfully implemented ANCS and then began to structure my application around it. At some point...
Hi,
I am trying to compile some RuuviTag application using nRF5_SDK_12.3.0_d7731ad
2 symbols are not defined,
APP_CONFIG_ADV_FRAME_SPACING_MS_MIN and
_ADV_FRAME_ETLM_SPACING_MS...
Hi nordic guys,
After the hid device delete the bond info but the PC did not remove it form the bond list,and i want the hid device to reconnect the PC quickly again but...
Hi,
in nrf connect app i see it is possible to update bootloader over ota.
How do i generate ota file properly? I tried generating zip and hex but the app says "no matching...
I have nRF6310, nRF2727.
I wonder if I can update the nRF24L01 firmware with the above board.
I wonder if there are any additional devices or other methods...
I am using ble_app_uart in one nRF52 EVK board(peripheral) and ble_app_uart_c in another nRF52 EVK(central) and sending data of Device under test through UART. When the data...
Hi,I want to use RTT in bootloader project.
First,i add all files(SEGGER_RTT.c ,SEGGER_RTT_printf.c,RTT_Syscalls_KEIL.c) to my bootloader project(Picture 1).
Second,I add...
hai
in nrf51822 the pins p0.01 t0 p0.06 are marked as analog pins in the nrf51822 DK.
i know that in arduino we can use an analog pin as an analog input as well as a digital...
Hello!
I am developing with mbed. According to nRFgo Studio, the hex file generated by the mbed compiler already contains the following SoftDevice: S132_nRF52_2.0.0 (Id...
Hi all, I'm working on sdk11.0.0 and s130 softdevice. In my project I want to send data coming from uart to ble and data coming from ble to uart same as ble_app_uart example...
Hi there,
I am working on programming the CTS ble service on my code.
In order to do that I also have to include db discovery.
#include "ble_cts_c.h"
#include "ble_db_discovery...
Hi,When I use nRF Connect app(IOS version) to connect my ble device,BLE_GATTS_EVT_SYS_ATTR_MISSING log information appears in my RTT Viewer(Picture IOS_Phone_Conncet).After...
Hello,
I tried as you mentioned using sdk12.1.0 buttonless_dfu and bootloader_secure example.
I didn’t modify anything except dfu_public_key.c.
As shown in the attached...
Hello,
I have a program that do an infinite loop in sd_softdevice_enable. How can i investigate ?
Loop is from 0x00009DEA to 0x00009DF2
Target is nRF52832 AA with...
Hi,
I am working on nRF52 with freertos + SDK13.0 + sd S132_4.0.2. I found the device will be trap in the xTaskIncrementTick of the xPortSysTickHandler when some task is...
Hi Nordic, can you please confirm the device ID for nRF51822 QFAA G1?
The HWID I discovered is 0x004A
Pls confirm so I can pull an update request for Black Magic Probe...
