I want to control GPIO toggle by PPI. Timer1 is in timer mode. CC[0] is 1000, and CC[1] is 8000.
I use compare[0] to toggle gpio18 by PPI. I also want to use compare[1] to...
Hi,
I use two evk board to connected and test the uart serialization sample(ble_s110_serialization), one is ble_app_hrs and one is ble_app_connectivity. But I have one...
I am getting get BLE_EVT_USER_MEM_REQUEST and BLE_GAP_EVT_CONN_PARAM_UPDATE event, when writing to ble device, sample code did not handle these event, and seems no document...
Hello:
Why do I erase SDK5.2 version of flash and read not, in SDK4.2 can. I tested nrf51_sdk_v5_2_0_39364\nrf51822\Board\nrf6310\flashwrite_example is a good example.However...
before i write the flash, it has been erased.so ,its value is all 0xff.
when i write 0x00 to flash address 0x0001,the value read out is not 0x00 but 0x01,and the value in...
I'm looking for a way to use the nordic uart service ( devzone.nordicsemi.com/.../ble_sdk_app_nus_eval.html) from Linux using the native Linux BLE Stack (BlueZ). My application...
Hi there,
Will any 4.1 features by making their way into the respective Soft Devices any time soon?
I would imagine 32-bit UUIDs would create some memory pressure on...
I am trying to use Eclipse+GCC for my projects. I found a similar issue as stated in the following post:
devzone.nordicsemi.com/.../nan-29-nrf51-sdk-no-project-files
...
I am having trouble getting up and running with the development kit (without the starter kit).
My setup is as follows:
The PCB antenna module is hooked up to the JTAG...
Hi,
In my design, there is a tag used by 24l01,It can transmit the temperature value.In the tag, the parameters are like this:
addrofch[0] = 0xe7;
addrofch[1] =...
Hello,
When the Ant stack want to transmit a packet while the BLE stack is using the radio, an event called EVENT_CHANNEL _COLLISION will be returned, is that...
Hello,
when the device NRF8001 starts Advertise, it sends out only one packet and unexpectedly terminates with a fatal hardware error in "ll_ctrl.s0.c" line 572. This happens...
Hi,
I'm trying to install Master Control Panel v.3.5.0 on Win7 64bit but I get the "Master Control Panel Setup Wizard Ended Prematurely" message. I have .NET Framework...
It would be very convenient to increase the output power of nRF51422/822/922 with at least 3-6 dB in order to get enough range. I'm currently not using nRF51422 for ANT, only...
with 1.16.0.3031 I cannot recover but I still can recover in Linux using a tweaked Makefile.posix
I don't remember this problem with previous version. Hence it must be...
I have tried to configure the nRF24A2 chipset in the asynchronous transmission mode by setting the bits in the extended field assignment. Unfortunately for some reason, it...
Hi,
I want to use 51822 to communication with 24l01,the 24l01 module is transmit temperature data, the 51822 is used to read the data from the 24l01.I set the parameters...
Hi,
I recently started on the nRF51822 Evaluation Kit and got the blinky code/example running. I then tried getting the Heart Rate application going but noticed when I...
Hi,
I want to use the nrf51822 to communicate withe the old module of 24l01p, in the module of 24l01p, the Address is
addrofch[0] = 0xe7;
addrofch[1] = 0x7e;
addrofch...
Hello,
I've been trying to get my TWI device working in conjunction with the BLE stack (i.e. s110 softdevice is enabled) on a nRF51822.
I found another thread with an...
