I am building an application for the nRF52840 on Linux just using west . I have been struggling with this issue for some time now. The linker can't find any mbedtls_ccm functions...
Hello, I am experiencing issues with the current measurements taken by the PPK2 when using the nPM2100-EK to power a device. The current drawn from the 2.7V power source ...
I have been trying to get MQTT+TLS to work on the nRF7002 DK and haven't been able to get the samples to connect to the MQTT Broker.
Is there a working MQTT TLS example...
Seeing the failure below and wondering a couple things:
How did the device get into this state?
How do I disable AP protection? The Kconfig GUI seems to indicate that...
Hi all,
I'm working on a custom board based on the nRF9160 and using nRF Connect SDK v3.0.2. We’ve developed the board in-house and integrated the npm1300 PMIC as part of...
Hello,
For our emission tests in an anechoic chamber we need to be sure that the BT antenna is up and running. Of course we cannot connect via BT from outside the chamber...
hi support team,
docs says we can program 54l15 external spi flash ,please refer to : https://docs.nordicsemi.com/bundle/nrfutil/page/nrfutil-device/guides/programming_external_memory...
I'm a little lost on the GPIO mappings from the code to the outside world. I'm playing with the UART example on the nRF6310 board. In the sample code, IO 16 is RX and IO 17...
Hi,
I am using ble_app_hrs application as a reference code.
in our case i have gpio interrupt for every 25 ms.
what should i keep BUTTON_DETECTION_DELAY for 25ms...
Does the lcd clobber the tmr0 and/or ANT ???
We just went through several days of working w/ ns on running ANT w/ RTC with a resolution of using sd_ calls.
Is the LCD...
Hi,
i am using nrf51822 custom board.
For our application i am using ble_app_hrs source code.
in that i have gpio interrupt for every 500ms, to get data from accelerometer...
For example, if I have a GPIO pin configured with low sense, and it goes low just before I call sd_power_system_off(), will the device return to System ON mode immediately...
Hello,
I've got a nRF51822 DK which I try to program with a SoftDevice using the nRFgo Studio (nRF51 Programming). My chip/programmer seem to recognized properly since...
Hi,
For developing our application i am using ble_app_hrs
in my case i have gpio interrupt for every 500 ms to get data from accelerometer.
question:
in heart...
Hi,
I am attempting to understand the timing of events when a mobile application connects to my nRF51822 based device. The reason being is that I have to enable the UART...
Hello,
Greetings, in the nRF24L01 datasheet, its mentioned that the module can work as a multiceiver, meaning 5 nRF24L01 module acting as PTx can communicate with 1 nRF24L01...
hi,
my customer using nrf51822 DK to have debugging software,the error occur in the attachment.
can you tell me something have Caused this problem?
thank you !...
I am using the code
err_code = sd_ble_gap_device_name_set(&sec_mode, (const uint8_t *)deviceName, nameLen);
I have made sure that nameLen is less than BLE_GAP_DEVNAME_MAX_LEN...
Hi
i am using twi_hw_master.c for i2c communication of accelerometer.
my accelerometer address is 0x18.
once i call
twi_master_transfer(0x18,dataW,1,1);
in...
Hi,
Can the value of NRF_RTC1->COUNTER be read safely from the main loop without first stopping the RTC or temporarily disabling the RTC1 interrupt etc? (nRF51822 or nRF51922...
I used the nRF51822 Evaluation kit and flashed the BLE_proximity example on to the PCA100001 board.
In the master control panel the USB dongle measured -46 dBm(Nordic_prox...
