Hi,
nRF5340 and SDK v3.0.0 I'm using.
Currently my nRF5340 based BLE device can be bonded with smartphone via passkey, after bond is done, the device stops advertising...
hi everyone
After using Android nRF Connect FOTA, the settings storage partition of my device was erased, which means that my device's PAIR information was lost and the...
Hi Nordic Team,
I'm looking to use the UICR->OTP region ( One Time Programmable (OTP) memory region within the User Information Configuration Registers (UICR)) on the nRF54H20...
Hello,
Now, I currently run Asset_Tracker_Template on Thingy91X
https://github.com/nrfconnect/Asset-Tracker-Template/blob/main/docs/common/getting_started.md.
And, I...
Due to production requirements, I need to obtain the device's QR code. However, I found that the QR code can only be retrieved using the code snippet below after calling Nrf...
Hi Nordic Support Team,
I'm currently experimenting with Channel Sounding using a couple of nRF54L15 boards.
I am trying to obtain raw I and Q samples so that I may analyze...
Hello,
currently i am configuring the networking stack on my project.
The goal is to use Matter's built-in Thread connection, to establish a Secure CoAP connection. I...
Hi,
I'm newbie in the RF Design. For my project nRF52832 chip is being used for BLE and NFC. Have a query regarding the NFC section which is listed below-
Please refer...
Hi all! I want to send data from a beacon (nrf51822) to a Pic microcontroller with the RS232 standard, what function should I use to send data? For example, I can use the...
Hi Nordic Developer Zone,
I also encounter a problem with enabling indications in my Android project. I want to enable Indications so I can gather informations store in...
Is anyone able to access the documentation for the Advertising Module?
Try this:
Go to the InfoCenter at:
infocenter.nordicsemi.com/index.jsp
Select the following...
Has anyone tried to plug an R3 shield to the nrf52 DK?
I was about to try, but it looks like the pins don't line up correctly - but then I have no experience with R3 shields...
Hello everyone,
I'm using the nRF52832, i would like to shutdown the timers, so i can enter the low power mode. In the datasheet tasks_shutdown for the timer modules is...
I have an application which receives commands from a co-processor via UART. Some commands are BLE-related such as, e.g. start-scan, stop-scan, connect, etc.
As the UART...
In nrf_drv_adc.c , there are loads of these ASSERT() macro calls:
ASSERT(mp_state == NRF_DRV_STATE_INITIALIZED);
But there is no variable mp_state. This will fail...
Hi! I have asked a question in this topic ( devzone.nordicsemi.com/.../) and now I can send one packet of 20bytes. What I cannot do is sending two packets at the same time...
I have nRF51 Dongle.
I can set it in BOOTLOADER mode and update firmware like:
developer.mbed.org/.../
I see the dongle in Device Manager/Disk drivers like "MBED microcontroller...
Hi all,
i have a little issue.
If i remove the bond information with app Master control panel, my slave cannot connect again with my phone. [Pairing Reject from Nordic_CTS...
I am moving from S110 and SDK 6 point something to S130 and SDK 10. I have my basic BLE code going but am unable to get the SPI back-in-action. I am using gcc and the s130...
I use NRF51822qfaa,s110 v8.0, now I use master TWI to drive the TWI bus chip.
the TWI bus chip Slave Address is 0x48.please see the below program .
question:
1.The...
this is the main program!
#include <stdbool.h>
#include <stdint.h>
#include "nrf_delay.h"
#include "nrf_gpio.h"
#include "boards.h"
const uint8_t leds_list[LEDS_NUMBER...
Hello,
I migrated from SDK 9 to 11 (S132) and i cannot receive anymore custom advertising (from another nRF52)
I receive another devices advertising events so reception...
