Hey folks,
I'm trying to modify the SPI Master loop back example into a 4 line SPI Master_Slave program. Whenever I change the Tx_Buffer_lenght from 10 to lsome other numbers...
Hi.
I am using S130 softdevice version.
Basically, I am using NUS Service and make a my own NUS central service as NUS_C.
It is correctly work at normal state.
When...
Hi All,
Please Reviwe for a attached circuit file(Chip ANT of nRF51822.pdf).
I also attach a datasheet of chip antenna applied for that circuit(SDBTPTR3015 Data Sheet...
to me it made sense that EN_AA settings are controlling the receiving pipes if an ACK has to be sent back upon receiving a valid packet.
then i thought that the settings...
I am using BLE_Gateway example defined in nRF51-ble-bcast-mesh to create an rbc_mesh over 2 nRF51422 devices . For now, I am just testing it out on 2 nRF51422; I will set...
Hello,
I see when you import an example from the pack installer ( for example pwm, ble, timer examples ) it arrives with the misc controls --c99 on by default , so I cannot...
Hi,
1.How to determine whether the nRF54L15 LFRC has been calibrated? 2. What logs can show the calibration completion event? 3. Or, apart from logs, what other methods...
Context:
VS Code
NCS 2.9
nRF54l15 custom board
Mac OS Sequoia15.5
peripheral_lbs sample project
Goal:
The goal of this project is to create a bluetooth beacon...
We are working on a prototype of nrf9151 with various sensors and nrf54L15. Our schematics designer says U13 (TCK106AG) may not be needed. Please let us know its use. regards...
I'm working on an ESL project using the nRF5340-DK. I need to enable the PAwR feature, which requires Bluetooth 5.4. However, my current program is written using nRF Connect...
When I downloaded it, I was prompted as shown below 。
I downloaded it correctly via the west command ：west flash --runner jlink.
I have 3 questions now：
1.What causes...
Hello Nordic Team! I'm experiencing unusual issues with GPIO pins on an nRF54L15 custom board. Specifically, P0.02 and P1.03 are not behaving as expected. Button Issues (P0...
Hi Team,
I’m using the nRF5340 Development Kit, and in our project, we have a custom slave device that communicates over QSPI. We’d like to interface this custom device...
Hi,
i acheived writting code that reconnects sequentially with multiple reflectors for my 1 initiator. When i am indoor i had good results, but yesterday i tried it with...
It seems that I'm getting different results reading QSPI flash from the APP vs MCUBOOT, with the exact same configuration. Writes appear to work fine from either, but MCUBOOT...
Hello,
I am new to nRF development. I am going through the nRF Connect SDK Fundamentals course.
I wanted to configure a GPIO on the nRF52833 DK board as an output and...
Hi,
I found that the NRF 54l15 can only estimate distance based on channel sounding and RSSI. On the bluetooth website it mentioned channel sounding accuracy being around...
HI
I have been using the DFU APP to create a zip file and update it.
However, this time, when I created a zip file to update and tried to use the zip file in the DFU...
Hi, Is there any resource or sample project to print the thingy:91x onboard sensor values to the serial using the printk? I tried myself with
#define BME680_NODE DT_NODELABEL...
Hi，the Nordic team
I use the SED device by system on mode.I found that my static average power consumption increased by more than 20 ua after I defined an IO port to use...
Hi, Using NCS 3.0.0 it would appear that the function sntp_simple_helper does not work with SYS_FOREVER_MS as a timeout value.
Problem: When we pass this value as a timeout...
