Hi,
I have been using nRF51822 with my Android app using Android's Bluetooth Low-Energy APIs.
In order to get more details, I am currently working on integrating the Android...
I'm looking at interfacing a typical Wheatstone bridge sensor to the nRF51822 ADC. This particular sensor only requires a mA or two for excitation and the output fits within...
When use the "nRFBeacons" app to update the info on my beacon the following happens:
Go to update tab.
Select "Connect"
Press "SW2" on beacon and see the LED begin flashing...
I am using s110 and nrf51822. I've set up up a long characteristic of 154 bytes.
Sending between 1 and 154 bytes works as expected.
Sending 155 - 160 bytes gets rejected...
Hi,
I tested the nrf beacon application, it allows only the beacons with company identifier 0x0059 (nordic's id). But i need to modify it to support all the device, how...
I use a app_timer_create() function to create a task(200ms once)
when in the task_timeout_handle() ,
I do something more than 200ms,
what will this timer going ?
Hi!
I use nrf51-pwm-library ( github.com/.../) to control brightness of LED RGB light source and it works ok till I don't want to adjust brightness slowly (dimming function...
I call the following function to delete old FDS records before I write a new record. It works well if I have only one old record. But when there are multiple records, it stops...
When I use nrf_drv_gpiote driver by sdk8.1.0. with softDevice 8.
I got HardFault_Handler when run in
handler(pin,polarity); in the GPIOTE_IRQHandler
How to deal...
Hello,
I use stack S110 V7.1.0 on nRF51822 (the device is a remote with 4 buttons).
Currently the remote send advertising frame with the pressed button into the data,...
I am writing code for nrf51822 with softdevice and an accelerometer is connected to the nrf chip. The accelerometer provides interrupt to nrf chip over GPIOTE whenever there...
Hi Nordic,
I am trying to extend DFU feature to my beacon application. Please help me with how to go about it. I went through the given tutorials on DFU/OTA, but I haven...
Hello sir,
I have develop my BLE_UART code is working fine with nRF52832 DK board but when i flash into spark fun nRF52 is not working. But i able to flash into Spark fun...
nrf51-Dongle keeps on connecting and disconnecting (to the PC) when inserted into the usb port of the PC.
Also it is getting heated up upon keeping it in the usb port for...
i am working on aes_ccm with '802_15_4_lib_keil.lib' , and i have build the target,but the result is not right. since there is no example with this lib,
now i have a big...
Hi,
I have a problem with (128 bit) custom service discovery... I have following setup; nrf51 with s130 in central role and Thingy with default FW.
In function on_primary_srv_discovery_rsp...
Hello,
I've moved my project to SDK 14 and SD 5 and that updates were working correctly in a loop (rebuilding app FW, merging BL+SD+APP, doing DFU). Today I've noticed...
I'm using a NRF52DK with Zephyr controller build attached to Bluez 5.45 to scan, connect and discover characteristics on up to 16 devices in parallel. While testing, everything...
Hi everyone,
I am using board PCA10040 v1.1.0, softdevice 13.0.0, Eclipse Oxygen. I am trying to scan my phone and communicate with it but the scaned UUID is increasing...
Suppose I configure RTC0 and RTC1 to have the same LFXO clock source (with a 30uSec tick) and start them in quick succession. Will their counters read the same value?
I...
I just started trying to get an IOT IPv6 application up and running. On the nrf51882 end, I have flashed the IPv6 COAP server. The LED on the device is happily flashing away...
