I'm writing a wav file from the nrf52840 board to the nor flash w25q128jv with a capacity of 16mb but it seems that I can only operate on the first 2mb, even when dividing...
Is there an AT command (For modem firmware >= 2.0.2) that can be used to validate whether the LTE modem can communicate with an external MIPI RFFE switch (for example on a...
Can Nordic share specific instructions on how to enable hardware tracing?
I've received the following patch from Tomasz, however I still see "trace clock missing" in Ozone...
Hi
our last product is based on nRF5340 and now we start a new design based on nRF54H20, and its essential for our design, i checked alot but there is no datasheet, reference...
just passed Cellular IoT Fundamentals while I was waiting for my nrf9151dk to be delivered... Now that I have the DK I can't get the dk to be provisioned...
I couldn't get...
NCS currently has a nice feature where the firmware versions are printed in the boot banner:
Is there a config option to also enable printing the nRF91 modem firmware...
Dear all,
after cutting the SB bridge to the QSPI chip and close the ones to get the pin free and disabled also qspi inside the nRF52840dk_nrf52840.overlay file I'm unable...
Reading the migration doc at:
<SDK>/components/softdevice/s130/doc/s13x_nrf5x_2.0.0_migration_document.pdf
I see there's a new fault handler type and an implementation...
Hello all,
I need to program nRF52 via the SWD pins. I cannot use the nrfjprog or J-link or Segger etc. I have connected 3 wires to the nRF52 - SWCLK, SWDIO and GND.
...
Hello to all
I'm working in an application that needs to be completely power optimized. In this program the device works as a scanner that if it finds an specific device...
Hi, I am wondering about the pre-made PCB's available on ebay, with a nRF24L01+. At a cost of $1, and with various forum stories over the Internet referencing issues such...
I am using NRF51422 S130. I have a master SPI configuration set up, and not using Nordic spi drivers provided in the examples. I think my configuration is correct.
1- I...
Hi,
We started out developing an application using the SoftDevice 1.0.0-3 (from SDK 0.9.2). We now need to upgrade to SoftDevice 4.0.2 (included in SDK 13.0.0).
We already...
Hello, I have some ideas to do for IoT and bluetooth. Already did some tests with MQTT raspberry pi and ESPs SoCs. Then I started to dive into bluetooth world and I found...
Hello,
I'm working with SDK 11 on nRF52832.
I want to get the IRK from a connection event. I need to identify the connected device.
My following code :
static...
I'm developing a multi-peripheral application on the nRF52832 that started from the SDK v13.0.0 experimental_ble_app_multiperipheral_pca10040_s132 example application (running...
I have two nRF52840-pdk's and two laptops. I was thinking to send test strings using the following Basic setup:
laptop1 - usb1 - pdk1 ....(coded PHY transmission)....pdk2...
I was able to write the code and put it to work on AN5 pin , and I found out that whenever I approach to the DK board he see it as a touch.
I connected to the pin a 10cm...
Hello all,
I am trying to make use of some Adafruit libraries for some sensors in my nrF52pca10040, the libraries are these two Adafruit_BME280.cpp , Adafruit_BME280.h...
Hello
In a schematic I saw the "SWO" connection appear on the Programming/Debug connector beside SWDIO and SWDCLK.
What's it for?
Of course it means "Single Wire...
I want to increase ble_app_uart_pca10040 app sample rate.
I have my own board with microcontroller and use nrf52832 as uart to ble.
I made pack length to 20bytes, I have...
