We use SDK12.10 Main.c (d:\nordic\5142xx\software\org-sdk12.1\nrf5_sdk_12.1.0_0d23e2a\examples\ble_central_and_peripheral\experimental\ble_app_hrs_rscs_relay.
My question...
Solved: Well, turns out delay and SCK doesnt work well together haha. I imagined the sck signal to be a background thread of some sort. I was wrong.
Hi guys,
at the...
Hi
Im looking for a developer in Denmark to discuss ble technology with. Im trying to get better to understand the technology, because i have some ideas involving beacons...
This system does not work if I enable the third Pipe (Pipe2) .
The system is working without any problem as one RX and two TX (Pipe0 and Pipe1).
The problem on enabling...
Hello,
i have read if not all posts about writing to FLASH while using BLE. But could not find the desirable method.
What i would like to do is to write to flash from...
Hello,
i have read all posts about writing to FLASH when using BLE. But could not find the desirable method.
What i would like to do is to write to flash from characteristic...
I'm trying to add the product key it shows an error "can not the product to your list" and therefore i will not able to access to the User guide
Thank you
Hi, everyone.
I've developed a custom board using nrf52832. I tested it and found that CPU core, GPIO and other peripherals work well, but BLE doesn't work at all.
I ran...
Hi,
Raspberry (SPI Master) -> NRF52832 (SPI Slave)
The code below execute event_handler of SPI with NRF_DRV_SPIS_XFER_DONE type. But RX buffer is empty. All bytes are...
Greetings,
I'm in the process of choosing a nRF52 module. I know of this link for the various modules www.nordicsemi.com/.../3rd-Party-Bluetooth-low-energy-Modules.
I...
Hello, I've been trying to get directed advertising and auto-connection working on an NRF51822 peripheral.
I'm using SDK V11.0 with SD130 v2.0.1
This is the scenario...
Hi,
I used the code ble_app_uart_c on board 10028 as a base for my custom board.
My board is nrf51822 QFAA based so I changed all occurances of nrf51422 to nrf51822...
Hello,
We are trying to communicate to this board ( www.adafruit.com/.../1697 ) that has nRF8001 at its core.
Unfortunately, our TX is only able to output BLE 4.2
...
I'm running on nRF51822, SDK 8 (not totally sure, I inherited the project), SD130 and mbed.
I've tried and failed with my own code to use pstorage.
I'm now trying a...
Hi. I'm using nRF51822AC, SDK12.2.0, S130.
The size of "s130_nrf51_2.0.1_softdevice.hex" in SDK is almost 300KB.
But chip's flash mem size is just 256KB. It's bigger than...
How is it used? And why to use it?
static nrf_saadc_value_t m_buffer_pool[2][SAMPLES_IN_BUFFER];
instead of
static nrf_saadc_value_t m_buffer[SAMPLES_IN_BUFFER];
Hi team,
we are doing project called indoor navigation using beacons.To get the good RSSI signal strength,in which position should i need to place the beacon. Can any one...
Hello,
I tried to flash an application to the nRF52832. First I flashed the softdevice, after that I flashed the bootloader and next the application.
The application...
We were doing various tests using PCA10040.
Then suddenly I can not connect to the PCA10040 board.
In the boot loader mode of PCA10040 board, connection is made.
What is...
