I'm looking into a rare issue on the BBC micro:bit V2 which uses the nRF52833 as its (application) microcontroller. I used to be familiar with some CPUs from the 80s but my...
I have shifted from silicon labs for BLE project. In Si labs we have burn BLE bootloader and BLE application separately. Do i need to do the same here in nrf controller? If...
I am unable to detect any i2c device when connected to the Nordic nRF54L15 DK kit. I have change the voltage from 1.8v to 3.3v and Tried and explore other pins in Port 0 and...
Hi All,
I have to implement an I2C Slave on my nrf52833 BLE project which is currently working (SDK 2.9.2)
I need some confirmation with the following step:
I have...
I am using the 54l10 chip, and after compiling the project, I will receive a hex firmware and a zip update package. The bin firmware and hex firmware in this update package...
Hi,
I faced with an initialization issue of combination two features: MCUMGR and UART_ASYNC_API. I get a crash right after the FW starts. It looks like the SW configuration...
Hello, I need to configure and compile a sample to send an audio stream (mp3) to the I2S interface.
I tried to put together some configuration from other samples but no...
HI,
I have very basic question: I plan to connect two devices on i2c to the nrf52. Can they both be connected to the same pins, and configured by software to select one...
I have been analyzing the Bluetooth snoop file on several Android devices, where the Android device is the Central (Client) and the peer device (nRF51822 with S130) is the...
Hi,
I am new to MCUs and I am trying to send information from NRF51 via UART (not BLE UART) to Putty. No matter what I try I can't seem to print anything on Putty. I started...
Hello!
I was copy template project from preinstalled folder to the desire one. When I opened program in new folder, the translate operation work fine. But when I pressed...
I would like to configure the connection timeout with the S130v1. This timeout is described in the following sequence diagram: infocenter.nordicsemi.com/.../group___b_l_e___g_a_p___c_e_n_t_r_a_l___c_o_n_n___m_s_c...
Hi there,
In the process of moving from SDK 10 to SDK 11, I've also been migrating an accelerometer driver over from using straight nrf_drv_twi code to the higher level...
Hello,
Is it possible to use easyDMA to transfer from GPIO to memory without involving the CPU? We need to read from a parallel bus for a short duration, without losing...
When setting up a 1Mhz square wave using NRF_PWM on the NRF52 or GPIOTE on the NRF51 while BLE is advertising, the PWM stops when the radio is active. The problem doesn't...
Hi,
I'm developing a BLE application for the nRF52 and I wish to use directed advertising and the whitelist.
I initialise the Bluetooth advertising using the following...
I have been using softdevice S130 version 2.0.0-7.alpha with SDK 11 in Keil using the pack installer. How do I change my project to work with the updated version that doesn...
Hi,
I believe there's a minor bug in low_power_pwm.c regarding pwm_state.
The routine low_power_pwm_start sets the pwm_state to NRF_DRV_STATE_POWERED_ON ; but it then...
I've a PCA10036 V1, I change the IC to nRF52822 QFAA-B016. With nRF5_SDK_11.0.0-2.alpha_bc3f6a0 and SD: s132_nrf52_2.0.0-7.alpha_softdevice, the programme started but if I...
I am troubling shooting some issues between my device and iPhone using nRF Sniffer.
One of the errors the sniffer captures is this:
Master to Slave: Rcvd Read By Type...
I will be using the nRF52 adc from -20C to 85C and am trying to determine if I need to calibrate and if so how much temperature difference I can have before it is time to...