Hi,
I´m working on a Zigbee-based environment sensor. You can find all related files here: https://github.com/Kampi/BeeLight
Now I have the following scenario: the whole...
Does the nrf54l15 have a register to specify the boot area? Similar to the NRF_UICR->NRFFW of nrf52833.Or does the nrf54l15 have to boot from address 0x00000000?
Hello,
I've been going through the BLE fundamentals course and things are going well. I'm using the nRF5340DK board and SDK version 3.0.2
I've gotten to lesson 3, exercise...
Hi,
I am working on the channel sounding feature on the 54l15 and I want to perform it sequentially between 3 reflectors and one initiator. I realized that after I make...
Hi,
We're at a point in our project where we're working through some regulatory testing for ETSI/FCC certifications with our BLE dongle board (nRF52840 + nRF21540 FEM...
Hi,
I'm using zephyr RTOS.
I'd like to put the cpu System ON Sleep Mode to conserve power.
Then, I'd like to restart the CPU with an interrupt or event from the comparator...
Dear Staff,
we have some Ublox C2909 TAG based on your nRF52833 chip.We need to program them for an RTLS project.
In particular we need to:
customize the FW here ...
Hi there,
I am using the nrfjprog to flash the nrf51822 via a J-Tag programmer. Here is the command I used in the command prompt:
nrfjprog --eraseall --programs softdevice...
Haw can I configure ble_app_ uart examples for bonding using? I want to connecting, transmit and receive data throw the UART only with 5 fixed devices.
Hi,
I updated to softdevice 8.00 recently, and found something different with softdevice 6.00.
When trying to program the new softdevice hex to the chip using nrfgo studio...
Hi,
I am using nRF51822 chip.
I am using the softdevice s120_nrf51_2.1.0. On top of that i am flashing the HRM central example given in the SDK nRF51_SDK_8.1.0_b6ed55f...
Hello, I'm fairly new are Nordic and have inherited a good project from a departing coworker. We are using Keil uVision 5+nRF51822+BLES110 softdevice.
She explained her...
Hello,
As mentioned title, when using printf with softdevice, "Stopped by a vector catch" occurred.
I am using my custom board(nRF51822 and s110).
And I am using IAR...
Hello,
When i try to set value of the gpregret using sd_power_gpregret_set and clear functions in on_write callback function, cpu gets stuck (i check it in debug mode). Can...
Hello
I'm trying to communicate with an sensor over the TWI HW interface during a BLE connection with the S110 soft-device, and every time I try to use the TWI bus the...
Greetings,
There is a bit of strange operation in UARTE peripheral in nrf52832 with the DK. In the simple code below, if both of the if statements with comments 'Check 1...
Hello everyone,
I have a strange issue with s110 + whitelisting + Device Manager + nrf51822 + GCC and hopefully you can help me with a good advice. It appears that the...
hi,
I am trying to integrate buttonless switch to boot loader as explained in the documentation and the hrs experimental example.
I am working on SDK7.2.0 and using...
Hello,
I installed the new nrfjprog but it fails to write my nrf51 dongle:
ERROR: nrfjprog failed for an unknown reason. Run the same command again with
ERROR: argument...
Hi All,
I would like to design a wireless system using nRF51822 with an effective range >100m LoS and 5m under water.The system is used as a ON-OFF control device powered...
