Using S120 V 8.0.0.3 alpha, processing a BLE_GATTC_EVT_READ_RSP,
received 0x16 bytes of data but there is more to read. Next call to
sd_ble_gattc_read using the same connection...
Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
SWI*_IRQ is using by softdevice to send event to application, I want to know which priority does softdevice set for them?
Does sd_nvic_critical_region_enter() disable...
I am a started guy.
I only need a bluetooth device (BLE) to check the signal and mac address.
What is the best choice?
I need the smallest and low powered!
Thank you...
Hello,
We are new in Bluetooth development world. We want to use Laird's BL652 module. At beginning we want to use smartBasic and later Nordic SDK directly. Is it possible...
HI Nordic Team,
I had a production run of 5000 units. Used nrfjprog script to program the nrf51 .
Used the following commands:
nrfjprog -f NRF51 -e
nrfjprog -f NRF51...
Dear all,
I have a project with a nRF51822 based on S110 and SDK10.
Almost everything is running fine, but every time I scan for devices, either by calling BluetoothAdapter...
Hi,
I am writing an application for nRF52832 that uses both Flash Storage and Flash Data Storage in SDK12.2. I want to know how to get the start and the end addresses of...
hello,will you please tell me which code i have to use in the sdk 12.2.0 for rf communication with nrf51822 and nrf24l01 .and also tell me which settings i have to do for...
Hi
I'm working on detecting voltage change direction(up or down) by using LPCOMP or COMP.
LPCOMP initiates as following settings:
detection: NRF_LPCOMP_DETECT_UP.
reference...
Hi,
in want to extend the DFU library (Android and iOS) with a function similar to setBinOrHex(). But instead of a filename, i want to give a byte array with the init packet...
I think there is a bug in Nordic provided code in this thread about fetching the offending PC in a hardfault handler:
devzone.nordicsemi.com/.../
The provided code is...
I have found these 2 threads in this forum regarding this matter but I am a bit stuck.
devzone.nordicsemi.com/.../
devzone.nordicsemi.com/.../
I want to port the...
It's been 14 months since the nRF 5x IoT SDK 0.9 was released.
Given Nordic's normal release cycle, that's an eternity!
Will there be another release or is it dead now...
Hello community,
Before I was using a pca10040 by Nordic evaluation board. The project, that i developed, is running well using the EB but when I change to sparkfun breakout...
Hello,
I'm working on nrf51822 with SDK9.0. I have two modules, one is working as a peripheral using s110 and another one is as a central using s130. Now central has a very...
Hi!
I am fairly new to programming micro controllers so apologies if I ask many questions.
I am using NRF52832. The situation is this - I have 2 devices and 1 host . After...
Hi all,
I've found the nRF52840 with USB but it seems a bit OTT for our application, something more like the 51822 would be nice, but cannot identify one, can anyone list...
