hts, HTC phone, nrf tools HTM, nrf51822,
every time when it's power up :
the once connect: error code 0x7A cann't read characteristic and 0x14 state change.
the second...
Our company needs wireless temperature sensors (can be externally powered or battery operated) and transceiver with 4 channel analog outputs. It has to be finished product...
I am toggling Value of slave through a button on nrf51822ek .This Value is displayed on MCP of dongle, but i have to get this value on terminal to send it to pi then through...
Hello, I am tryong to use to masters to communicate with two accelerometers.
Q1_ I found the following image from Nordic's website that shows SPI0 pins but there is no indication...
In the nrf51 series reference manual section 12.1.9 it states that there is hardware protection that prevents write instructions from being executed and that there is more...
Hello, I have established the connection between two pca10001 boards, one as central and one as peripheral using multilink_central and multilink_peripheral. I have serial...
Hi,my friend,
Now,I use nrf905.Situation is as follows:
I use the NRF PCB circuit of data manual.Nrf905 work, often loss of data.
1.The Product host is to use the stick...
Good day,
we would like to use a central and a few (4) peripherals. Peripherals would stream small chunks of data (few bytes) very frequently (10-50Hz). What are the drawbacks...
To reduce power, I'm trying to find the best approach to minimize the cpu load when sampling an accelerometer at a high rate, e.g. 1.6Khz. Is there a way to DMA a sensors...
I am writing a crc checker for the application and the softdevice . I am using a s120 version 2.0.0 it currently has a upper boundary of 0x1D000 is this a hard boundary for...
Hi everyone.
I am making an application which combines two services (ANCS and Nordic UART). I compare the advertising_init() function from the two provided examples (ble_app_ancs_c...
Hi,
I've been searching the devzone for TWI examples, and preferably an example with MPU6050. Here are a conclusion of stuff that I found, but as some of them were for...
Hi ,
I tried to upload the application firmware using OTA service through MCP, I successfully get connected and the transferring of application hex file also gets successfully...
Hi Guys,
once again, I have strange behavior of my code.
In my code I try in loop after ble_event received change PWM from 0 to 255 for my motor device. In debug logs...
Dear,
Please, could help me ?
My knowledge in RF is basic.
I am developing a system to use 8 RF channels (nRF24L01 +) simultaneously.
I'm using Balum 2450BM14A0002...
Hi,
I’ve just ordered a few nrf51822 (from seedstudio ) and waiting for them to arrive.
They come preloaded with SoftDevice 6.0 or 7.0. with a pre-flashed OTA boot loader...
Hello, I am trying to connect a Nexus 6p running Android 6.0 to the NRF52 dev board. I have tried numerous ble examples in the SDK, but nothing ever appears in the nRF Master...
So if I start a program in debug mode some zero-inited static variables are non-zero.
ldr r1, =__etext
ldr r2, =__data_start__
ldr r3, =__data_end__
subs r3, r2...
I'm attempting to use the app_trace module. I've set it up as follows:
int main(void)
{
// Setup tracing. Also sets up UART.
app_trace_init();
app_trace_log(...
Hello,
I know that this question has been asked a few times, but I am a little desperate after trying to get debug logging over the Virtual COM Port to work. Here are the...
Hi,
I've recently got some brand new nRF51 Dongle, and used nRF51 DK. The problem is that DK is not recognized by mine PC. There's actually some example program (heart...
