Hello, I hope you are well.
I created a new driver for an i2c accelerometer with 2 gpio interrupts, but it does not build properly. When calling `static const struct device...
Hello everyone,
I'm working in a ble project that use uart interface. When I sent string data in nrf connect app, the uart_event_handle is not called.
I started my project...
Hello, I am working with a nRF54L15 and using a TF-M build (cpuapp_ns). SDK and toolchain are currently v3.0.2. NRF_SECURTY is enabled (by default) and here's the relevant...
Hi,
I’m working on a Matter application using the nRF Connect SDK v2.9.2 . I’ve added the AirQuality cluster into my device with sub-sensors: CO₂, PM1, PM10, TVOC, and Temperature...
nrf5340DK
NCS 3.0.0
if I use sample zephyr/samples/boards/nordic/system_off it works fine and i can wake from sw0 press. but if i move the sys_poweroff() call int a...
Hi Team,
Recently we did a network related testing for our CL5G modem (nrf9160) and observed a problem, in this test we used a nmap tool, this tool will search for open...
Steps to reproduce the problem
Create a new application based on the Matter Light Switch example of the SDK 3.0.2
In prj.conf set CONFIG_CHIP_FACTORY_DATA_BUILD=n
...
Hi everyone,
This is my first time using Nordic nRF SDK, so i hope that I'm not asking for anything too stupid, I'm having troubles in adding nrf_logger.h into a project...
I've noticed that the BT-SIG listings for s132 v6.1.x https://launchstudio.bluetooth.com/ListingDetails/64933
and s140 v6.1.x https://launchstudio.bluetooth.com/ListingDetails...
Hello everyone!
We are developing a device with the nRF52840 SoC and using mbed-os for developing firmware.
Everything works and runs normally when using mbed softdevice...
51822+LIS3DH
I have tested my board and got the current consumption value. I use slow advertising only and the interval is 2 seconds. Follow is the result:
1. advertising...
I am using SDK15.0 and added the functionality of nrf_storage into the ble_app_uart in order to store the results of scan (which are kept during run time in an array in RAM...
Hello,
I am use nRF52832 chip in my project.
i am write data in flash by crating record id. For write record in flash I use below code,
For read flash I use below...
we develop 52832 from the project "ble_app_hrs_freertos" , in nRF5_SDK_14.2.0.
occasionally， xQueueSendFromISR returns without pdTRUE in Interrupt handler.
so xQueueSendFromISR...
I designed a custom nrf52 board using the ( nRF52840-CKAA-R ) as the chip. I am trying to program the board using P20 of the nRF52840 development kit and using Kielu5 and...
One of the answers pointed to here www.nordicsemi.com/.../Download , but there is no firmware there unlike the equivalent nrf52 dk page www.nordicsemi.com/.../Download
I found similar questions, but none that were marked as "answered".
I have a working version of "nRF5_SDK_160.0.0_98a08e2/examples/ble_peripheral/ble_app_uart". I also have...
Hi,
I have 3 images that I need to flash on the device (nrf52840 on the nrf9160DK if it matters). They are a trivial boot manager and two application images. I have read...
Hi I plan on using two UART modules from the nRF52840 which is why I am trying to use the app_uart_init however at this stage I keep getting the following error:
undefined...
Hello, I've been having problems getting the AWS_FOTA sample working on a nrf9160 DK.
At first, the device got stuck as it was downloading the firmware update, at 2%....
