I am trying to get a good handle on the difference in average power consumption between BLE point to point and Zigbee on an nRF52840. We have battery powered products and...
Hi, For my project, I need to design a BLE packet sniffer which scanning the 40 channels. Therefore, I need 40 dongles are connected to a computer that can read and transfer...
I am writing code to get a nrf52840 DK to associate with an existing 802.15.4 coordinator using the 802.15.4 API module within SDK 15.2.
I've called "mlme_scan_req" and...
Currently, I am able to use Mqtt Publisher or Subscriber with only one Nrf52 device. I can ping to the device with link-local address.
I am using Nrf52832 with SoftDevice...
Hi everyone,
After days of figuring out how CMake works, I try to write a CMakeList.txt myself, and decide to put my progress on this community. Right now, using CLion with...
i am using nrf 52832, i got SAADC example code from sdk. that code done by using timer. i could not understand timer section. Is available SAADC simple example code without...
Hello everyone,
as indicated by this question https://devzone.nordicsemi.com/f/nordic-q-a/35692/adding-nrf52-dk-to-github-mesh-demo-for-thingys/138327#138327 I am trying...
I want to tested RF performance ，so i hope send cat-M 6RB@0 signal. For example, the circled part of the picture: ,it's send 6RB@22 signal。please tell me AT command.
Re: nRF52833DK, s113 and nRF5_SDK v16.0.0
It appears that nrf_sdh_freertos.c needs to be modified to support JUST_WORKS and LESC because the softdevice_task() in nrf_sdh_freertos...
Hi
I am working this tutorial . At the end of this, I copied and executed the contents of advertising_init() function but it became NRF_BREAKPOINT_COND.
When debugging...
I am trying to use the GPS from the Thingy:91. Due to the unavailability of Power Saving Mode (PSM) in roaming with my local provider, I am considering what options are available...
I am trying to see/set preprocessor options and they are not visible. I have seen the tutorial which says
project options >> code >> preprocessor should be the way to do...
Hello nordic, I have used the nrf24 before with ARM, and this go around its AVR, not that that changes much but looking for some help. I'm familiar with how this chip work...
Hello! We are designing an iPad app that will occasionally connect to our device over BLE. The app is kind of a maintenance/service app that will query various information...
I am trying to get the IEMI and HWID in my code. I was able to read the IEMI as a client ID using the following API.
nct_client_id_get(client_id_buf); printk("Client ID...
Hey there!
I´m developing an small wearable sensor based on the NRF52840 (SDK 15.0.0, S140 6.0.0) on a custom board. The sensor will log data on an external NAND flash and...
Dear Community;
I have a NRF9160 DK. I have flashed a program to it, and it works fine. The program connects to LTE every 10 minutes to send some data over HTTP. However...
I recently picked up an nRF52840 dongle and I cannot seem to get it to work properly on a very new Win10 machine. It does seem to work properly on my Mac however so I believe...
Hi,
I cant login to devzone from Firefox. But do not seem to have the problem using Chrome. I tried clearing cookies and site data. But couldn't login to the forum. It is...
SDK:nRF5_SDK_16.0.0_98a08e2
Hardware：52832QFAA
I refer to the code of ble_app_buttonless_dfu to port to ble_app_hrs_freertos but the following problems occur during the...
Hi,
I've been experimenting with the Mesh SDK (v3.2) on nRF52832 boards. After doing some end-to-end latency experiments, I've come up with some questions associated with...
51822, S130, SDK11.0. In order to save current, I disabled fast adv and set the slow adv interval to 10seconds. The current is low now, but I am facing connecting issues with...
