nRF52840 NCS 3.0.1 RCP
I just installed the NCS 3.0.1 SDK. I am trying to set up a border router on a Raspberry Pi 4.
I followed these instructions on the Raspberry Pi...
Hello,
I have a legacy project that is using nrf5 sdk v17.0.2. I need to add the BLE DFU functionality to this project based on the nRF52840. Are there any examples on...
We are trying to evaluate nrf9151 for working with Soft-SIM. Are there any instructions for configuring the Soft-SIM through AT command mode, or do I need to use another mode...
I was doing some developement for a custom board on NCS v2.9.1 when i noticed some of the changes i was making in my prj.conf weren't being set in the application. My impression...
In my circuit I have a MOSFET which disconnects the battery. There is a GPIO pin which turns this device on and I'm using regulator-fixed to drive it during start-up. A short...
We are currently using ncs 2.9.0 on an nRF5340. We use the BT_HCI_OP_VS_READ_VERSION_INFO to determine at runtime what version of the BLE stack is present. This information...
Hi I'm trying to load a custom board with nrf9160 with the Serial LTE Modem, and route the AT commands to the UART from a coprocessor (ESP32C3) I have followed the guide on...
Good afternoon.
I´m using nrf51-dk with SDK 9.0.0, s110 softdevice and uart nordic app on mobile. I have a program in my nrf51-dk that it sends and receives data between...
Hi all,
We are using nRF51822-QFAA-R7 to develop our HUD system. The BLE connection is not stable some time.
For most iphone 6/6s, the BLE can connect for a short time...
Hi. Im beginner in BLE.I have a question. how PipesOpen bitmap in Pipe Status Event create? is it sent from smartphone application to nRF and nRF sends them in Pipe status...
Hello everyone,
I am using 3 nrf24L01 on arduino Uno boards.
One arduino is the coordinator and the others are nodes.
The coordinator send on a specific pipe a value...
hi, I am a beginer with 24le1. as we know, when the chip in standby mode, it can be waken up by rtc2 or RF interrupt.
if it is waken by RF, how do I know how long...
Is it possible to have a gatt characteristic user description being read only?
I'm currently using this configuration, but the "nrf master control" android app allows me...
in this tutorial
devzone.nordicsemi.com/.../
i download .zip version and copy that example but it show me this error and say download this
and this is my folder...
Can you specify any chip in which we can have distance parametre also from receiver to Transmitter.
Please provide any link for its Evaluation board also.
Regards,
...
image description (/attachment/464b945b7dfd5bcb858b14aa400f0933)
Hello everyone,
I am using the ble_lbs example when i checked in the Master control panel initially...
Hi,
The program I'm testing is mainly based on the example code Martin provided in
devzone.nordicsemi.com/.../
First test was that to read sensor data (MPU6050) by...
hi. Im working with nrf8001 type c in a self-designed board and im using arduino library driver on github by nordic. my mcu is stm32 and i ported library to my mcu.
when...
I'm using nRF 52383 and need one of the GPIO pins to clock an external device with 4MHz clock.
Can any GPIO be configured as clock output or is there a specific group of...
Hi, all.
I want data read from gyro sensor through i2c, and then send it through bluetooth equipment.(PC or iPhone and so on)
My development environment is like below...
Hi everybody.
I am making a custom circuit which using external LDO with output is 2.5 volt.
Then I use this 2.5 volt as VCC_nrf for the nrf51 chip which using internal...
Has anybody used an nRF51822 (e.g. on nRF 51 dongle / Adafruit BLE Friend) as a central talking with a peripheral like the TI SensorTag? Is there a tutorial / example code...
