I have modified the NUS-CDC application for the Dongle so that I can now scan, report available Peripherals, and connect to a specific one. I need to be able to cleanly disconnect...
We're designing a board using the Thingy:91X as a reference design. We're trying to determine if all of the power components are required.
The nPM1300 appears to provide...
We're designing a board using the Thingy:91X as a reference design. We're trying to determine the best approach to antenna tuning.
On the original Thingy 91, it uses the...
We're designing a board using the Thingy:91X as a reference design. We're trying to determine if we can use one Ignion antenna, shared for the LTE and GPS.
On the original...
I'm working on an nRF device (S112 SoftDevice) that acts as a connectable peripheral to an iOs central. The application only has data to transfer every 5 minutes, so I'm trying...
I was wondering how I can update my current code (see below) to reuse a single socket for multiple HTTPS requests, rather than opening and closing a socket for each HTTPS...
Hi,
Our team is interested in WiFi location service in Cloud Services.
https://www.nordicsemi.com/Products/Cloud-services/Location-Services
However, under the WiFi...
Hello!
everyone:
I use nRF51822 UART Demo(ble_app_uart),test uart interrupt receive data, baudrate is 38400.
if start advertising ,rx loss data ,else rx receive data perfect...
Hi,
I have develop my firmware on on nRF51DK which has n51422 chip.
But my actual hardware has n51822 chip.
So my firmware is working on development board (nRF51DK...
Hi Guys
I've got a strange problem where a binary that works fine on a nRF51822 QFAC does not run on a QFAA
I know that the difference between these two devices is the...
I need to define a few constant arrays for IR implementation. Currently, I define them as
static uint16_t but it takes up a lot of SRAM space. How do I move them to program...
Hi,
I have a setup (in SD310.2.0.0) on nrf51422-qfaae0 in which I'm hoping to receive data on multiple ant channels from multiple networks, but I cant seem to understand...
HI,
with the new version of the bluetooth website, i can not find the link to overview the profile,service,characteristic and something else related to it.
thank you.
Hello,
I am working on a wearable device at the moment. To support iOS and Android at the same time, I have implemented ANCS and nRF UART on the circuit.
When working...
I successfully run "ble_app_hrs_c" on BLE_Central example at 38,400bps on the PCA10001 device.
My modification on PCA10001 board as follows;
cut out 32.768KHz X...
I want to store the max possible data on flash using pstorage , but I noticed that I have to increase the number of Maximum number of flash access commands PSTORAGE_CMD_QUEUE_SIZE...
Hello,
I have got a problem with use SPI. I get hard fault after call spi_master_open(), exactly when sd_nvic_ClearPendingIRQ function is call.
This situation is so specific...
link text from this post , i want to make code, when i press button,device goes into sleep mode.so i use this post's code in ble uart app. my code is here.
/* Copyright...
Hello all,
I am new to this domain.
Here is my case:
I am using the Atmel SAMA5D35-EK rev D. board. I was facing JTAG connectivity issues over J-Link.
My purpose is...
Hello!
I have Adafruit evaluation board with NRF8001 module and it works perfect.
I also tried to develop my own board with microcontroller unit and NRF 8001 module...
I have a few nRF51 dongles I wish to use with ANT+ for wireless mesh communication between some robots. I want to connect each to one ATmega 1284p and another Arduino Mega...
I'm using nrf25822, I flashed my firmware using DFU and I discovered the a memory regions starting from 0x0002A000 is written
this memory isn't written when I just use...
