I'm searching for a software engineer who can help us getting OTA support between nRF52810 and PIC16 MCU.
nRF52810 must have command- and data mode over UART, Pic controler...
I want to be able to read the gyro and accelerometer values from the MPU6050 sensor.
As a base start I downloaded the NRF5 SDK V15.3.0 and modified twi_sensor_pca10056 program...
Hi. I'm using nRF52832, SDK13.0.0.
I should use SHA256 and MD5.
I made my code as below.
NRF_CRYPTO_HASH_CREATE(init_packet_hash, SHA256); NRF_CRYPTO_HASH_CREATE(init_packet_md5...
Hi. I'm using nRF52832, SDK13.0.0.
I want to use SHA256 as below.
output32Byte = SHA256[input32Byte];
Which function or example can I refer to?
And also I want to...
I tried to port the example "ble_app_ipsp_initiator" to pc-ble-driver and run on Linux. The peer device is another PCA10056 device running ble_app_ipsp_acceptor. The problem...
hi...
i want to use two uarts in nRF52840 , one uart to one pc and another uart to another pc .Data should be transferred and received between the nRF52840 and pc how can...
Hi, i'm using two nrf52840 DK ev kit. One it's the central and one the peripheral
After the connection I need to save power at the peripheral board, because the cpnsumptio...
Good morning,
I am running the UART example from SDK 14.2 (example/ble_peripheral/ble_app_uart) on a brand-new NRF52832 development kit (PCA10040).
On the master side...
Hello.
I try to periodically updated data in my characteristic that way:
As soon as I connected via "nRF Connect", function " sd_ble_gatts_hvx" returns: NRF_ERROR_SVC_HANDLER_MISSING...
Hi all ,
I have SHT31 and I can read Temperature and Humidity value by NRF52 . But I want to create 1 service for display it on smart phone with the RH (name: Humidity,...
Hello,
I would like to measure the voltage of circuit GND by using the embeded SAADC of nRF52832.
But unfortunately I have no vacancy of GPIO to connect GND.
Could you...
I have set up a nrf52840 kit to upload data to nrf cloud via bluetooth but the data on the cloud is displayed as a hexadecimal number(1,2,3,4,5,6,7,8,9,A,B......) I want to...
I am not seeing a transition to BLE_ADV_EVT_SLOW. The transition I see goes from FAST to idle, without a transition to slow, from the configuration I don't expect to be in...
I am trying to implement a timer using nrf_drv_timer.h and nrf_timer.h, however, the handler never gets called.
I first create a timer, then define a timer handler and finally...
Hello everyone! I am trying to program a nrf52832 sparkfun board through a nRF52DK. I have already gone through the pin connection guide succesfully and I can flash succesfully...
Hi there,
I could program the HEX file to nRF51DK via nRFgo studio successfully and the board seems to work fine as well. And then, I try to read back the HEX file from...
I am just wondering if it is possible to use the 52840's USB interface to create an R/NDIS type interface . The intention is to maybe create a WIFI/Cellular based Network...
Hi,
I am testing ble_app_att_mtu_throughput in SDK 14.2.0 between two nrf52832 DK board. One is act as a central and other one peripheral. I am placing these two boards...
Not a question, just to tell you that in ble_gatts_attr_t Struct Reference, documentation of « uint8_t* ble_gatts_attr_t::p_value », a « @ref » Doxygen markup has been produced
I have one pca10040 board, I want to realize the data transfer between the nrf52832 and the PC by BlueTooth, I use python3.5+PyBluez. When the nrf52832 is running the "ble_app_blinky...
The following lines are copied from the SDK15.0 documentation:
<pre>
Supported boards:
- PCA10040
- PCA10040E (nRF52810 emulation on PCA10040)
- PCA10056
- PCA10059 (support...
