Greetings!
I am using Wireshark along with an nRF52840 dongle to monitor BLE traffic between a mobile app and connected peripheral and periodically I see some "L2CAP Fragment...
Hello, I am using the nRF54L15 board, and trying to connect to the Adafruit SHARP 400x240 monochrome LCD display .
I got the display driver alone to function just fine after...
Hi,
I am trying to perform a DFU using SMP over BLE. My setup has NSIB and MCUBoot enabled and thus I am able to perform DFU for MCUboot and Application using nrf device...
Hi all,
I'm trying to use uart2 on my custom nrf9151 board, but I'm stuck. As I understand, I use i2c1 so I can't use uart1 and i2c1in parallel, so here is why I wnt to...
Hi - I am seeking clarification on a topic as I am a little unsure on the correct way to do things.
I'm using an nRF52840 and porting an old Firmware from nRF5 SDK to NCS...
Hello,
I'm moving my project from SDK1.9.1 to SDK3.0.2. Project is based on peripheral_uart sample (UART part is removed since it is not necessary).
I have encountered...
Hi, i'm using NRF5191 with DECT.
DECT modem: 1.0.2
App: hello_dect sample
In datasheet I found that NRF9151 support various band: 1,2,4,9,22
and I'm using these value...
I have added button in my project and used bsp_init() to initialize it. All functions in bsp_init() returns NRF_SUCCESS but if I push my button even gpiote_event_handler(...
Hi Folks,
i have implementet a sleep mode by using only the RTC timer with the 32KHz OSC and the WFI instruction. The current consumtion is around 1.7µA (all peripherals...
Hello,
We have some problems with nRFgo Studio on the one of our computers.
Firstly, it takes a long time to flash firmware - about 15-20 seconds:
Secondly, we...
I have interfaced a vibration switch with nRF51822 Pin 19 using external pull-up. When there is no vibration the switch is either at open position or close position randomly...
UPDATED WITH IMPLEMENTATION
Is there a way to know what is triggering a chip boot :
Power off (battery replacement or deffective electrical connection)
The watch...
I have an old project I am trying to recompile for nrf51822 but have been programming with the most recent MDK on my station. The project is asking for old Device Family pack...
Hi all!
I just tried to compile the DFU example from the nRF51_SDK_7.1.0_372d17a and I keep getting the building error:
Referred Memory Range 'IRAM2' is undefined
...
Hello,
Does nRF51822 has a MAC adress when we buy it ?
If yes, is it possible to have two nrF51 with the same MAC adress ?
If yes, can we buy a MAC adress range and...
The new tutorial points to this github repository.
Then there is this instruction:
Download the NUS central example from github.
Open it in Keil by opening the file...
I think the following sentence in the new BLE Central tutorial is a typo:
Flash the S110 Softdevice it to your central device using nRFgo studio.
I think you mean...
Hello,
I'm trying to setup a gazell application that could use the same resources of the Nordic SD.
Using the keil package manager, I switched the package configuration...
I'm going to configure nRF51822 chip as a spi slave.
And there are no more pins for the connector.
So I am trying to connect SS pin to the ground pin, instead to connect...
Hello
I'd like to write my own application for flashing nrf51822. It will add some additional information info hex file.
How can I burn hex file into the flash using...
