Hello,
I have a custom PCB with the nRF5340 chip. I’m able to flash the board using a J-Link. I’d like to rename the device so that it advertises a specific Bluetooth name...
Hello,
We are currently using the nrf52840 for development using Zephyr v3.7.99-ncs1 .
We want to use the UART in low power mode and therefore, we have used the zephyr...
Greetings!
Briefly summarized: I am trying to generate SPDX files for our project, but I hit some roadblocks while running the west spdx command. I found a way to workaround...
We are implementing a Joiner device using OpenThread on the nRF5340 (with Zephyr, NCS v3.5.99-ncs1-4). After successfully joining the Commissioner's network ("Join success...
I purchased a SIM data from ILIAD and I am trying to connect to network, but the AT command AT+CEREG? : +CEREG: 0,4 instead of 0,5 as I expect.
The lte_lc_connect_async...
Hi I am using an nRF54L15 with an external watch crystal. I have notice that depending on the manufacturer of the crystal I have to use a different internal load capacitor...
I am using the `mcumgr` subsys to enable the DFU (Device Firmware Update) capabilities in a custom device that also features a custom (non mcuboot) bootloader. In order to...
Hello, I am developing with pc-ble-driver using python. I noticed that the Bluetooth connection becomes disconnected when I alt tab out of the gui I made. Is there a solution...
Hello,
I am using SEGGER Embedded Studio together with a nRF52832 and I am trying to read an EEprom register containing a 32-bit floating point value in four bytes (register...
Hi,
I try to use the BLE to send data to a smartphone but I have a issue when I try to flash my nRF52 DK, using eclipse. I get the following error :
No source available...
I am using the example ble central devices from the SDK 8.1. The example provided prints out to pin 19 (the on-board LED). I wanted to change the functionality to print to...
I am trying to add ADC to my program per the nordic examples on GitHub.
Using GCC, SDK12, nrf51.
These are the errors I am getting: (sorry for the formatting of this - code...
Hi,
SDK12 does not have Pstorage. I want to show you how to add it.
Steps:
Copy the pstorage folder in SDK11 into the SDK12 \components folder.
Open...
Hello,
I've been working on a project for some time now and prototyping it with replacement atmel ic's like the at mega328 and bluetooth modules and other stuff in the...
My custom board sometimes freezed on initialization process of bootloader (SDK11 dual_bank_ble_s130) when after long running and reconnect the power.
However the symptoms...
I am running the ble_app_hrs example and it runs as expected.
However, I tried removing one or more of the services from services_init as well as the corresponding advertisement...
I implement a card emulation and the card itself doesn't conform to 14443A-3 crc check. I need to disable crc check on card selected event
NRF_NFCT->RXD.FRAMECONFIG...
I've been running a hand soldered prototype board for about a week in an outdoor location where it gets hot and cold (mainly hot), and I noticed it was no longer visible on...
I am trying to add the spi and twi drivers to the ble_app_template project, but I keep running into errors. I am using the SDK 12.2.0. How are we supposed to go about adding...
Problem:
In our project we have one peripheral which can be bonded to many phones at the same time (of cause) while they are still close to it, thus connected via OS. ...
I am trying to scan and connect to a Polar H7 HR belt (which I can do), with m_scan_mode = BLE_NO_SCAN. Once this happens, I understand they are supposed to bond, and at that...
