Nordic Support,
My product uses the nRF52840 chip and nRF52 SDK 17.1. I have a feature request to support hosting multiple peripheral connections, each with a unique advertising...
Hey everyone,
Does anyone here have experience with firmware OTA updates over the JIO NB-IoT network? The process seems a bit different since JIO Cloud always sits between...
Hello:
The latest nRF54L15 Errata for Rev 2 shows that the previously reported "GPIOs can exhibit radiated emissions" is no longer present in the Rev 2 SoC.
Can you please...
Hi, this is a very broad issue that i am having, because i dont know the source of it. I am simply unable to use the bme68x IAQ library. i have downloaded the external bsec...
Greetings!
I am using Wireshark along with an nRF52840 dongle to monitor BLE traffic between a mobile app and connected peripheral and periodically I see some "L2CAP Fragment...
Hello, I am using the nRF54L15 board, and trying to connect to the Adafruit SHARP 400x240 monochrome LCD display .
I got the display driver alone to function just fine after...
Hi,
I am trying to perform a DFU using SMP over BLE. My setup has NSIB and MCUBoot enabled and thus I am able to perform DFU for MCUboot and Application using nrf device...
I have a nRF51DK. And I would like to be able, to enable/disable the softdevice with 2 buttons.
Button 1 on nRF51DK --> Enable Softdevice
Button 2 on nRF51DK --> Disable...
Hello,
I am working on nRF51822 S110 softdevice 8.0 and SDK9.0. I am creating paired and unpaired states and the system will goto unpaired only if it is unpaired from the...
I know nrf51 timer0 can be configured for 16,8,24 and 32 bit modes
and timer1 and timer2 can be configured for 16 and 8 bit modes.
But what can I expect the value to be...
I'm going to star a new product development using nRF51422 supplied by a 3V battery. Since it is a low cost product the idea is to use the nRF51422 internal DCDC to provide...
Hello,
I'm using an external chip that decodes my RF transmission and outputs the data on two pins DAT, and CLK (data and clock). Currently I'm reading the data with GPIOTE...
We have written our own softdevice, but now we have a question about the stack pointer.
I read in the softdevice specification that the nordic softdevices share the stack...
I have been trying to establish a link that will feed sensor data into my com port via a Bluetooth uart bridge. I got my closest today by doing the following.
Load SDK10...
I'm having trouble making a single bank dfu mode with 128k NRF51822 chip.
Here's the problem;
Works fine when everything(SoftDevice, Application, Bootloader) is all...
Hi,
I am a newbie to Nordic BLE.
A make error occurs when building the heart_rate_collector example code of nrf51-ble-driver_linux_0.5.0 on my cross compile environment...
Good morning, i have windows 7 and at this moment i have installed "Gnu tools for ARM embedded Processors", "GnuWin32 ‐ GNU Make utility", "GnuWin32 ‐ Core Utility", "nrfgostudio...
Hello,
on our custom hardware design, the hardware reset won`t be executed after programming with nrfjprog.exe, until complete new boot with disconnecting Vcc.
After reconnecting...
We are going to use nRFgo - Bluetooth direct test mode to evaluate the nRF51 device RF performance, and we need to load the DTM (Direct test mode) application to the device...
Hello
I have an nRF51822 serving as s supervisory micro for an embedded Linux board. Two GPIO pins from the main CPU are hooked up to the nRF51822 to implement SWD for...
