Hi, could you please tell me if my assumptions below correct?
Measuring a (ratiometric to VCC) analog signal and selecting VDD_1_2_PS as the reference selecting AIN_NO_PS...
When I initialize the SoftDevice with SOFTDEVICE_HANDLER_INIT(NRF_CLOCK_LFCLKSRC_XTAL_20_PPM, false); // Sets up Crystal Source to 20ppm 32.7628kHz
The project I based...
I am trying to make a product with NRF8002B. I finally have the product prototyped. The user will connect to the device, beep, light up, and track. It will always stay on...
Please,
It seems that "Flow Control" signal is not available on nRF24AP2-USB.
EVENT_TRANSFER_TX_START event message appears only one time after the first data packets...
I am looking for cheapest (up to few hundred USD) and simplest Arduino basic solution to track real-time RFID tags distance (also direction if possible) without additional...
Hi all,
I am new to Nordic semiconductor but I could be interessed by nRF9E5. To check if it could fit my requierement, I would like to know if it possible to configure...
hi,
i am using one central and 18 peripherals. i am unable to send data to one particular peripheral from the central .plz help me to identify a peripheral in the group...
Hello, We were interested in a new SoC nRF5340, but I would like to determine some points in advance:
peripheral blocks remained the same as in nrf52840. Or were changes...
Hi there,
I would like to add the device address of a central to the whitelist on my peripheral. Is this possible without bonding? So I set sec_param.bond = false in pm_sec_params_set...
Hello.
I am working on ble project and using uart communication between bluetooth and stm32. I need to reinitialize uart module in case of any error in event handler but...
1、nRF52830。Does the dongle included with the product support the over the air packet capturing function of Bluetooth?
2、We need Bluetooth to grab packets. Do we need a third...
Hello,
nRF52840-DK
SDK: 15.3.0
s140
OS: Ubuntu
IDE: SES
Our application is has a notify characteristic that works when attached to the JLink debugger. I can get...
Hi, I am using nRF51822 on my custom board with SDK 12.2.0. I use DFU bootloader, and can update application in BLE from DFU mode with bootloader (dual bank mode is used)...
I am using the nrf52 Dk with nrf52832 chip and i want to write bulk data onto the dk and then when i read the dk from the mobile app nrf connect, i want to see the written...
Hi,
I am trying to integrate the DFU service into the ble_app_uart example. I am using NRF51822 with SDK 11. I was able to successfully run the ble_app_hrs with dfu. So...
Hi. I'm using 2x nRF52840 DK's + eero pro.
I've been noticing some stability/longevity issues with examples/thread/freertos_coap_server in nRF5SDKforThreadandZigbeev3209fade31...
Peer Manager in recent SDKs supports up to 20 peers but SoftDevice functions like sd_ble_gap_whitelist_set() and sd_ble_gap_device_identities_set() are able to handle up to...
Hi, I am trying to get BLE packages with the nRF52840 Development Kit without using Wireshark or other external app. Does anyone have any solution? Thanks in advance
I have followed this tutorial from this link but cannot get it work.
I have 3 loop. For the first loop of sending data it will have a delay about 1s and until 2 finish...
A%dBBCCDDEEAABBCCDDEEAABBCCDDEEAABBCCDDXX = 40bytes
1) In Termite:
Data is complete and in sequence when until 6 only.
A0BBCCDDEEAABBCCDDEEAABBCCDDEEAABBCCDDXX A1BBCCDDEEAABBCCDDEEAABBCCDDEEAABBCCDDXX...