I'm interested in creating a time of flight algorithm and am trying to calculate what to expect for accuracy.
Is it possible to get an IRQ from when the sync arrives at...
hi all ,
how to enable GPIOTE PORT and IN[n] event simultaneously ?(not same pin)
i enable the GPIOTE to trigger interrupt event.
one for the keyboard which need multiple...
Hi All,
I am using nRF51422 with softdevice s310. And implementing Cycle speed and cadence receiver. most of the data processing is fine but i am facing one problem.
...
Hello Nordic Team,
I have a problem with programming the nRF24LE1 chip.
I am developing a small system, which consists of a uC STM32F4xx and a nRF24LE1 Radio Module. The...
Hi,
I'd like to learn about the app compatibility for the new OTA DFU that ships with the new SDK 6.0.0 and S110 7.0.0. I am using a nRF51822 board and I've observed that...
I'm curious to know if there is a tool that allows easy design of a GATT server DB that is portable across dev platforms (the nrf518 EK, my Android/iOS dev environment etc...
Iam trying to display the uart data as a scanned response.nRF51822 receives the data from PIC and it is displayed as scanned response during advertising.the problem is nrf51822...
I'm working with nrf24l01 module and use it in BLE beacon mode.
My main question is how can I decrease the visibility range to 10 - 20 santimeters?
(by some schematic...
Hi Support team,
My search for nrf8001 port to Arm-m3 landed me on a thread , where the support personnel has provided a link for a port to lpc1769 in the last comment....
Hi,
I would like to add sensor data in mesh network to be able to send data in certain intervals. How is it possible when I create a sensor model for mesh client and server...
Hello. I have a nRF52832 DK and I'm trying to modify the SPI example code found here:
/nRF5_SDK_15.0.0/nRF5_SDK_15.0.0_a53641a/examples/peripheral/spi
I'm using the nRF52832...
Hello Guys,
I have brought this nrf52840 to try BLE mesh. I tried connecting it to the PC and it was working fine, later I tried dumping the file into the board through...
Hey Nordic and co-nordic developpers,
Just to show some capabilities here at work I want to compile and run the mesh demo on the 10 Thingy52's we have here. I am currently...
Hi Nordic,
Could you please help me ! This is an urgent matter!
Based on this discussion , there is an error rate of actual baudrate comparing with the desired one.
...
Hello everyone,
I'm trying to use the new SDK 15.0.0 and the S140 soft device V6.0.0. I would like to use the LE CODED physical layer and set my TX output power, but when...
Why did the softdevice handler's API change?
sorry for a general question. I used SDK 13. and Now, I am porting my software to SDK 15. So, I have simple question. Why did...
My application is based of the UART example, I have a repeating app timer that fires every 5 min's to do some tasks, I also utilise single fire timers (initiated for events...
Ok, so I am using nRF52DK and trying to figure out to how to send up to 6 packets of data from custom service that sends 6 16bit values per packet. When I send one packet...
Hello,
We have a custom boards that powers a NRF52840 module from a 1.8v voltage regulator coming from a 3.6v battery. We also connected the positive pole of the battery...
I am new to embedded development. How do i physically connect the sensor to the board?
Is it possible without any additional equipment? What is important regarding pins...
Hi,
We want to certify a product embedded nRF51822 chip, with BAS and IAS defined by Bluetooth SIG.
Requesting SIG certification for it of a certification body, we were...
Hi all,
getting burnt out from searching the fourms and finding dead ends or outdated answers so just posting a question quickly.
Somewhere along the line my nrf51DK has...
