Hi all,
I'm working with the nrf51422 and the nrf51822 and I was wondering what the current status of the over the air DFU system is.
I'm using SDK 6.0 and I managed...
nRF24l01+ at a transmitter module one time successful transmission show & after 1 sec failed also . if any doing programming with atmega32 ,please send code for TX & RX ....
Hello,
can the radio notification and radio disable APIs be used to use the radio hardware from the application layer?
Background of my question is, that I have an application...
Hi,
I am using central s120 with peripheral s110. The connection to the peripheral is depending on the name advertised by the peripheral.
When connection is done, the...
Hello,
I am trying to ecrypt some data in order to send some data encrypted in the MINOR and MAJOR adverts of the device.
I used this code to ecrypt the data ( this is...
Hi,
i use anRF51822 with soft device 7.
I run the UART app on my iPhone 4s with ios7 and on the nrf51822 board the ble_app_uart with keil uVision5.
Both devices connected...
Hello,
I upgraded nRFgo Studio software to version 1.17.0. Installation goes OK but the application crashes every time I try to launch it after installation process.. Then...
Hello,
I am using nrf5340 audio BIS headset with other LE Audio Tx test. The nRF Connect SDK version is v2.2.0.
During the sync process on both sides, the headset error...
I'm trying to transmit audio data between two nRF5340DKs. These boards share timestamp information via the wireless time synchronization method here: https://github.com/nordic...
Hello everyone
I'm currently trying to make dynamic endpoints on my matter device. I changed the .zap file to accomodate all the possible endpoints (16) with clusters...
hello Nordic
i am working with nrf52832 and nrf52840 as peripherals for a central node (one has nrf ble device and one does not)
i downloaded the image for the nrf52840...
Hello Nordic Support Team,
I am working on an nRF52-based project on a custom PCB using the E73-2G4M08S1C devboard ( https://www.cdebyte.com/products/E73-2G4M08S1C ).
...
Hello
I designed a custom board and now I have to put the code in the nrf52840 module (from raytac). I have been using the nrf52840dk to write my code and now I want to...
I wanted a COAP Server running on nRF5340dk with DTLS and NS-Target without success. Whenever there is an attempt to connect to it from outside the app freezes, eg. shell...
Hi,
I had a working project for nrf Connect NCS 3.0. I don't know what happened, but now I can't even create a new build configuration. Every time I click on "add build...
Hi
I want to use nRF54L15_DK run RSSI test
I know Desktop App on PC "RSSI Viewer" only Support nRF52 series,
Q1：How can I use Desktop App to run RSSI test?
Q2：Can...
I am currently working on a project involving the nRF52832 SoC using nRF5 SDK v15.0.0 . According to the nRF52832 Product Specification v1.4 , it is mentioned that P0.00 ...
I am receiving packets in monitor mode on a nRF7002DK. I need some advice on how to interpret the signal value. From <modules/nrf_wifi/fw_if/umac_if/inc/system/fmac_structs...
I'm developing a solution using the nRF9160 and would like to confirm the correct method to completely disable NB-IoT mode so the device operates exclusively in LTE-M.
...
By default the GRTC peripheral is not cleared when started via sys_clock_driver_init . This is because nrfx_grtc_init calls nrfy_grtc_prepare , however NRFX_GRTC_CONFIG_CLEAR_AT_INIT...
Hello everyone
I created a custom board with reference to thingy:91 for the antenna part. The board is 50x50 mm in size.
I tested the board and there are no problems...
