Using the nRF Beacons app, but cannot see the battery condition of each beacon. Is this already implemented - if so how to turn on? If not how is it implemented?
Using the nRF Beacons app, but cannot see the battery condition of each beacon. Is this already implemented - if so how to turn on? If not how is it implemented?
Hi All
I am doing a BLE based project using nRF51822.Where i need to handle the message [with UUID] by using ble_gatts_char_handles_t.
so, can any one please share information...
I have a central application and peripheral application that are based on the multilink-central/multilink-peripheral examples.
I've modified them to run on the PCA10001...
Hi All,
I'm using nRF24L01P for TX device and want to receive packet from nRF51822 RX device.
nRF24L01P TX device Register settings are as follows;
Reg.EN_AA=0x00...
I am trying to develop for some nRF51822 mbed boards, and I would like to use the S130 SD to enable both central and peripheral behaviour. The machine I'm using for development...
I'm using the nRF51822 eval kit
I have installed MCP but after starting I get pop-up: Master Control Panel has stopped working
In nRFgo Studio / Device manager pane...
Hi all:
I refer the "IoT_SDK_step_by_step.pdf" to setup my raspberry_pi ,then I can successfully ping the DK_board from raspberry_pi.
my question is , I can't ping the...
Hi everyone!!
I've gotten the ipv6_coap_server example to run on the nRF51-DK,and I use raspberry pi as gateway and I can got the bt0 interface after connecting to the...
I would like to add LIN-bus to a project of mine.
The hardware part is easy, connect a LIN interface ASIC to the UART of the nRF5x.
But writing my own LIN-bus SW driver...
Hello World!
I am trying to interface an LCD with nrf51-DK. I basically need to send 3 signals - SCLK, MOSI and SS to the LCD. I have modified the spi_master example from...
I am working with a sensor which has a programmable configuration register. After changing this register, I have to reboot the sensor. To do this, I need to temporarily suspend...
Hi, I try to send data through SPIM to my panel(Sharp Memory LCM), and I success get the picture (only part of the picture).
The reason why is that function can only...
I have migrated to SDK 9.0 primarily to take advantage of some of the Advertising Mode functionality in Device Manager. While I was still in SDK 8.1, I had implemented functionality...
When you download win driver (from www.nordicsemi.com/.../72324929 for instance). There's only a win32 dll/lib provided.
However, modern development are often made on 64bits...
I am using nrf51822 with s110 softdevice. My goal is to allow pairing and bonding to a single central device. Once its paired and bonded, it should not allow connection and...
In one of our projects the nrf51 shares the SPI to a device with an STM32 microchip. To be able to successfully share the SPI channel, I'd have to put the SPI pins of the...
Hi,
I am currently using nRF5_SDK version 11.0.0.
I have 2 nRF52832 development kits.
On the soft device side, i am using S132.
My understanding is that this (S132...
I want to make a blinky program from scratch and have no idea how to settup keil. I would prefer something step-by-step. I have been able to use the precompiled example, but...
Hi all!!!
I'm new in here.
I'm reading document with link: developer.nordicsemi.com/.../index.html
In Figure 1, I see a phare: "IoT Device". Is the "IoT Device" nRF5x...
Hello,
my setup is nrf51822, with SDK 10.
I try to create application to drive I2C components and I get compilations errors:
In function 'Hal_I2cInit':
../../../nrf5...
