I'm looking into a rare issue on the BBC micro:bit V2 which uses the nRF52833 as its (application) microcontroller. I used to be familiar with some CPUs from the 80s but my...
Hi everyone,
I'm working with the nRF9160 and trying to configure P0.19 as the UART TX pin using Zephyr. Here's the configuration I used in the device tree:
uart1_default...
I have shifted from silicon labs for BLE project. In Si labs we have burn BLE bootloader and BLE application separately. Do i need to do the same here in nrf controller? If...
Hello,
I am using nRF Connect SDK v3.0.1, together with the Find My add-on. Test case TCG013 of the Find My Network Self-Certification Test Cases R1.7 is failing on the...
I am unable to detect any i2c device when connected to the Nordic nRF54L15 DK kit. I have change the voltage from 1.8v to 3.3v and Tried and explore other pins in Port 0 and...
HI: D:\ncs\v3.0.0\nrf\samples\bluetooth\peripheral_uart Using the nrf54l15DK board can run peripheral_uart examples,connection is disconnected. However, when I use the nrf54l05...
Hi,
I'm working on software for a design incorporating an Ezurio module that uses an NRF54L15 chip.
I'm currently using the peripheral_uart example as a base for early...
Hi, I'm newbie developing with nRF51. I'm working in Firmware for a ble central role that can read all the macs of ble peripherals roles near. I want to event or function...
Hi all,
I've a problem that drives me crazy for some day.
I installed all SDKs, and trying to write some BLE apps. Everything works fine but i cant't find where pstorage_access_wait...
Hi,
I want to implement stack tracing to check stack overflow and remaining stack. I followed the implementation given in example github.com/.../memory_watcher.
Memory...
Hi
I am coding a s130 NUS example.
The base example is sdk8.1.0 ble_app_uart peripheral example.
I added central part from Github sdk8.0.0 ble_app_uart_c...
Hi
I've installed the new tools in version 7.5.1 to support the new nRF52 family. While working on the nRF51 again i found out, that the old parameters i used for programming...
Hi,
I'm working on a project where nrf51 modules should communicate with each other. For that i'd need to set characteristic that can store string. Now i've done that ...
Hi,all.i call function "sd_clock_hfclk_release(); power_manage();" and want my device to sleep.as this,my device's current is 2.2mA.what's wrong ?Can someone help me?
I have a master device using SPI interface , write data to nordic SPI salve and send data to cell pohone.
But ,the master device SPI wirte data is fast, the nordic will...
hi all,
since i am new to nRF24L01+ device, kindly any one provide me details regarding range that can be supported by nRF24L01+ device.i already try to find out information...
Hi,
I am attempting to create a secure BLE connection in security mode 1 and level 3.
I noticed that when I simply call sd_ble_gap_authenticate with MITM = 1 it seems...
Hi,
I would like to save the most energy when going to sleep mode. In particular, I want to turn off the radio while keeping just RTC timer on.
So, after shutting down...
Hi there,
When I tried to send data chunk (it's about 8K) to phone side according to this , the speed is much slower than 1K/s, and what's more, it's disconnected with...
Hi,
I have a problem in CRC of setup message for nRF8001,
and I already try the CCITT-16 algorithm with below conditions:
Poly = 0x1021,
Init = 0xFFFF,
Ignore all...
Hi,
I want do RSA on NRF51822. The build environment is GCC. And the develop base on S120. The RSA need 1K to do calculation. If I enable the RSA calculation, the APP may...
