Hi
I am working with the zephyr ZMS sample application. I am using SDK 2.9.0, and I built the application for the nRF54L15DK (nrf54l15dk/nrf54l15/cpuapp). The sample works...
Hi, I want to set different gap event length for different peripheral on a ble central: 1 link with high throughput and 4 links with low throughput.
The sdk is 17.0.2...
Is there any documentation on what peak data rates are available on the nRF9151?
While the Cat-M, Cat-NB1 and Cat-NB2 standard max data rates are easily available, I have...
Hello,
I've seen multiple posts related to this question, but they're not very recent so I wanted to check if there's an updated answer.
Are non-simultaneous multi-image...
I have an Ubuntu Machine where I successfully installed Zephyr SDK and toolchain following instructions given in the official getting started guide here . I was able to compile...
Hello,
I have a custom PCB with the nRF5340 chip. I’m able to flash the board using a J-Link. I’d like to rename the device so that it advertises a specific Bluetooth name...
Hello,*
I'm new to nRF Connect SDK environment, but I'm used to work with Zephyr.
I'm actually confused using west.yml file. I created a new application based on existing...
Hi,
I designed before my board for 2 layer PCB and i used the coplanar waveguide with ground-plane in the bottom. now i want to move to the 4 PCB layer and i choose the...
Hi, I'm porting my project from SDK8.1 to SDK10.
I replace static app_timer_id_t m_beacon_timer_id; to APP_TIMER_DEF(m_beacon_timer_id);
to avoid hardfault when creat...
Hi all:
I modified DFU-BLE to make it suitable for S130 on nRF51822. I made the following modifications:
On "dfu-ctr1_pt_add"
ble_gatts_attr_md_t cccd_md;
memset...
Hello!
Until now I am using a nRF24L01 with johanson balun (2450BM14A0002) and MIFA.
I want to add a power amplifier to my nRF24L01 project. Can anyone give me advice which...
Hi
I have a programming issue with nRF51822. I am using the nrfjprog.dll to program this microcontroller in my test equipment via J-link Plus. When I have programmed a...
I am using single NRF24LU1P-F32Q32-T ic.i am using it only as a TAG transponder card .i wanted to know that can we program it to transmit only if there is no other controller...
hello everybody,
I measured the current consumption in two cases : in the advertising mode the current is around 4 ~ 5uA, & in the connected mode, the current is 160 uA...
Hi,
I am new to forum and to Ble. sorry about my week English.
I am working on a project where I am reading adc value every 1s and sending it over ble. So I have written...
Hi,
I'm using nRF dev kit with Softdevice 1.0.0.3.alpha. The device shows advertising state at LED1 as it should, however i can't detect "Nordic_UART" via nRF Master Control...
Is the advertising interval between two packets P1 and P2 defined as:
Interval = P2_start - P1_stop (time between packets)
or
Interval = P2_start - P1_start (time...
In a project I worked on using softdevice s110 v. 7.1.0, if the receiver hadn't enabled notifications, sd_ble_gatts_hvx would return an error, so I used the following construct...
Hi,
I want to advertise multiple UUIDs, one after another
Do I have to stop advertising, or is there a way, that I can update the struct in the background?
Currently...
