Hi,
Parameter uint8_t ble_gap_scan_params_t::filter is present in the documentation, but not implemented.
Checked for SDK 5.2.0 and 6.0.0.
devzone.nordicsemi.com...
After I get a Disconnected() event, I want to start scanning again, therefore try to call StartDeviceDiscovery() again.
IsDeviceDiscoveryOngoing was checked before.
The...
Hi, I wanted to ask a question regarding sending data.
I currently have external memory that will send out serial data (SPI) to the nordic microcontroller. I have saved...
Recently, I try to programme nRF51822 DK communicating with nRF2401e1 DK,unfortunately，which does not success. With setting radio configuration: TXPower,frequency channel...
E:\BLE\work\nrf51_sdk_v6_0_0_43681\nrf51822\Board\nrf6310\s110\ble_app_hids_keyboard
SDK 6.0.0
Softdevice 7.0
When I connect to Android 4.4.3 device(Nexus7 II) will...
E:\BLE\work\nrf51_sdk_v6_0_0_43681\nrf51822\Board\nrf6310\s110\ble_app_hids_keyboard
SDK 6.0.0
Softdevice 7.0
When I connect to Android 4.4.3 device(Nexus7 II) will...
I have been trying to understand and get the “ble_app_template” running this weekend, but I keep running into errors. For example in
static void sys_evt_dispatch(uint32_t...
Hello， for the past I've been trying to migrate unsuccessfully my code from nrf51 to nrf52840 S140. Now that I'm unsuccessful, I'm trying to eliminate the possibility of a...
Using FreeRTOS to run nrf_cli. When Serial is not connected (as in RX,TX,GND) the board goes into a reset loop.
There are a few things that seem to help:
Don't run...
hi,
i have tried to write data into flash memory, but i can not, i can read the data from memory.
i had followed your instruction as this link
infocenter.nordicsemi...
In my project, an android phone is needed to connect to two ble devices. All my ble devices are nrf51822. The android phone can connect to and receive data from every device...
Hi,
to investigate a timing problem in my Bluetooth stack, I've hard wired the Radio ADDRESS and END events to a GPIO pin using the PPI. The ADDRESS event is used to toggle...
Hi,
I'm developing a FW with a lot of services and characteristics. Since I added the ANCS service, I have the "NRF_ERROR_NO_MEM".
Configuration : NRF51822_XXAC / S130...
hello everyone,
i use nrf51822-QFAA(256kb flash,16kb ram).i want to use sdk12.3.
at first i can't build the project,after i install some tools, i can build it ok.
...
i am using nRF5_SDK_13.0.0-1.alpha_055eef3 s132_nrf52_5.0.0-1.alpha_softdevice and used examples\dfu\bootloader_secure\pca10040\ for secure DFu OTA .everytime i try i get...
What's the current consumption for a Timer on the nRF52832 when it's used in Counter mode? Do Timers require the 16MHz or 1MHz clock when configured for counter mode?
Hi Vidar,
I am planning to start devlopment on the nRF52 and I would like to use GCC ARM with Eclipse. After having read your post "Development with GCC and Eclipse" and...
Okay so the issue is a little more complicated than this.
Phones used for testing were htc m8 (android 6.0) and lg g5 (android 7.0).
Ble chip running on a linux OS using...
Hello, I'm using this code(observer):
github.com/.../nRF51-multi-role-conn-observer-advertiser
SDK9.0.0
I try to add DFU function, now can enter dfu mode and iPhone6...
Hi Nordic Team,
Can you please share any information regarding Indoor Location Tracking feature/application that nRF52840 can support? does this have AoA/AoD? and can this...
