Hi, my friend,
I've been with nrf905. I use a 16-bit CRC check.
But I encountered problems in use:
1.Nrf905 16-bit CRC check format is CRC-16(IBM):X16+X15+X2+1 or other...
I have two custom PCBs, each of which has a microcontroller and an nrf24L01+. Everything related to the transceiver in the designs are complete duplicates (with the exception...
Hello,
I've built a small BLE-device based on the nrf8001.
With my Iphone I can discover this device and I am able to connect to it and listen to notifications of the...
Our pcb is used for gps location data. We have a nrf24L01 nordic chip as the micro process or between the gps module and wireless module (2G). Our engineer needs to capture...
Hey folks,
I'm trying to modify the SPI Master loop back example into a 4 line SPI Master_Slave program. Whenever I change the Tx_Buffer_lenght from 10 to lsome other numbers...
Hi.
I am using S130 softdevice version.
Basically, I am using NUS Service and make a my own NUS central service as NUS_C.
It is correctly work at normal state.
When...
Hi All,
Please Reviwe for a attached circuit file(Chip ANT of nRF51822.pdf).
I also attach a datasheet of chip antenna applied for that circuit(SDBTPTR3015 Data Sheet...
Hello,
What I want to do is to store custom data to flash using FDS in "disconnected" event.
When I try to write the data in "disconnected" event, the write_flag is...
Hi,
I have 52832(ble_app_multilink_central 12.2) which is connected to 5 51822 (experimental_ble_app_blinky) modules.
How to make 51822 not discoverable or not connectable...
Hi, I'm interested in the nRF5 SDK for AirFuel .
I have received a task to replace parts in a product which formerly used wireless charging and the CSR BLE chip.
I think...
If anyone will ever have this error:
When using c++ and singleton the use of operator new is not possible.
I found the solution in this post: forum.arduino.cc/index.php...
Hello everyone,
Lately I have been struggling while trying to run "BLE Advertising, a beginner's tutorial". My hardware consists of NRF51822 and PCA1000 dongle. I use SDK_11...
I am working through the TWIS Slave and TWI Master mode drivers Example using SDK 12 with the nRF52832 PCA10040 board and having issues. I am using Minicom through the terminal...
I want to use the last page of codespace for storing a single 32 bit word of non volatile data. I am failing so far and I think I just don't understand the page numbering...
Hello everybody
I am working with the Raytac BLE Module "MDBT40", which is based on nrf51822.
And I am testing example project "ble_app_uart" in the SDK6.1.0 now.
...
I would like to confirm my understanding of Problem sending 6 bytes to multiple services using sd_ble_gatts_hvx
I use nrf52832 sdk13.0.0
BLE SPI is master. I dropped...
Hello,
I connected the nrf module to jlink as described:
• vdd(nrf)-----3.3V
• gnd(nrf)-----gnd
• SDO(nrf)-----SWDIO(jlink)
• SCLK(nrf)-----SWCLK(jlink)
• 3.3V...
I've run into some interesting behaviour in my code and wanted to see if anyone can clarify for me. It seems as though the SPIS module doesn't set the MISO pin as high impedance...
Hello,
I built a simple I2C application for the LMP91000 and I was successfully able to configure it to read the status register.
However, I tested to see if I could...
