Hi,
I'm using nRF SDK 16 for my application on the nRF52840 custome board. When I set both parameters (i.e., support for coded PHY and 1M PHY ) in the scan initialization...
Hi all,
I'm working on a Nordic-based system involving multiple nRF52-series chips exchanging high-rate sensor data over both radio and SPI links. The setup involves two...
Howdy!
I am attempting to develop a system using an nRF52840 and an ADS131M04EVM (ADC). Our application requires us to collect data at a high sampling rate (>= 16k SPS...
I have a nrf9160 DK but when upload SLM application to it i can not send AT commands to it over it's usb port but in asset tracker application it works i want to modify SLM...
Finally we got our prototype boards and proof of concept firmware code done and we are a bit stuck on the average power consumption over time for the entire sensor that is...
We are implementing a Joiner device using OpenThread on the nRF5340 (with Zephyr, NCS v3.5.99-ncs1-4). After successfully joining the Commissioner's network ("Join success...
Hi,
I have integrated Neuton’s “Transport Type Detection” pre-trained model into my firmware, running on a nRF52840dk. For collecting 9-axis IMU data, I’m using the ST X...
i am using latest "master control panel" v4.0.5 and latest "nRF tool box" v1.16.2
and use sdk 5.2(its compulsory)
soft-device s110 v6.2.1(its compulsory)
and PCA10028 with...
Hello everyone,
Could anyone tell me which pins are the programming pins of the nRF51822 chip for a QFN48 packet ? How can I program it on my custom PCB?
thanks..
We are planning to use nRF52 for its superior computing power in an application. Unfortunately it appears that the throughput is more limited than on nRF51. Since we need...
Hi,
I used two 51822 modules for my project. One should send a byte and other one should receive.
I used the exact same configurations of radio examples (transmitter and...
I am trying to read an analog value on the GPIO port into my application. Looking through the examples, there aren't any that help solve this problem as the ADC example is...
I have tried to follow the installation instructions and have installed nRFGoStudio, the Keil MDK-ARM, and downloaded the latest nRF52 SDK. I also installed all of the device...
Hello,
Iam a beginner to NRF51 and Iot.
I want to be able to send messages from raspberry pie to NRF51 dk and vice versa via Bluetooth.
Iam using a generic Bluetooth dongle...
Hi ,
I've just started using a Nordic's product : an nRF51 422 QFAC develepement Kit
I was running tests by loading examples on this board when I lost the connection between...
I am building my application up on the blinky free rtos. I want to use RTC and ble stack. i am initialising RTC1 first and ble stack stact.
The problem is that I am getting...
I am using nordic nrf8002 BLE with a breakout board & not a developement kit. I gave 3.3v supply in different combinations:
(1)3.3v to vdd pin-1, GND to vss pin-4
(2)3.3v...
Is any SDK available which has single bank BLE DFU bootloader source code?
If No then is it possible to convert dual bank BLE dfu bootloader into single bank BLE dfu bootloader...
I am trying to Migrate from Sdk 6 to Sdk 11 .
Here i am facing problem in discovering Custom Characteristics .
I can successfully add service and 2 characteristics without...
Hi!
I'm building an application with one custom service containing a few characteristics, all of which are to be indicated upon. When using the Master Control Panel Android...
How can I calculate the maximum throughput for an application running on the nRF51822 and the S110, when connecting to different kind of Central devices?
