Hello Nordic team,
Environment:
SDK 3.1.0
nRF54L15
UART / RS-232
I am seeing different UART TX timing depending on whether I transmit from inside the UART RX...
I’m working on a product that has been in the field and working for many years with nRF5 SDK v15.0.0 / softdevice 6.0.0. Now we want to add extended BLE advertisements and...
Hi everyone,
I am trying to add a bootloader for the NORUB126 board.
Before adding the bootloader, my application did not use any bootloader and everything worked correctly...
Hi there,
1. I want to sniff BLE LESC bonding session in tshark/CLI not in Wireshark/GUI. And decrypt it in the same session using LTK. The idea is to increase the time...
Hi, I need the nRF91 SiP SUPL client library (for A-GNSS via SUPL on my nRF9151, NCS v2.9.1). The official download process is not working for me, same problem many others...
While configuring a scene, the blind device is not visible in the scene settings screen, so it is not possible to set or save the blind position as part of the scene.
Steps...
I build contact sensor example (use nrf connect sdk v3.2.1, nrf52840 chip) and try commissioning with apple home kit (use homepod mini), device commissioning succeed but cannot...
Hello! I'm currently working on a circuit design where weight and size are critical factors. Could you please tell me the minimum dimensions and weight of this chip? Thank...
I've made a new project as I had to change some hardware than the previous one.
The code seems fine, but I'm not able to load the libraries in the project.
A red underline...
When an ESD shock to the PCBA causes the nrf52840 to reboot, what reset code should we expect to show up with hwinfo_get_reset_cause()? RESET_BROWNOUT?
Using Zephyr NCS...
Hi! I am trying to use the LE Audio application and one of the samples in it, by including the necessary source files, and Kconfigs in my project. On the network core, I am...
As per the doc , when I use a smartphone (the base version is Android 12) to touch the NFC antenna, I should see a pop-up window:
3.Confirm pairing with ‘Nordic_HIDS_keyboard...
Is it possible to promote my project here: complete Zephyr development environment running solely on Raspberry Pi 4 Bookworm OS? If nothing else it does provide information...
Hi There,
During the transmission and reception performance test, I found that the LE1M's maximum sensitivity was only -92 dBm, while the LE2M's maximum sensitivity was...
Hi,
we have a Gateway board that uses the nRF52832 with the nRF21540.
The firmware running on the nRF52832 is a slightly modified version of the HCI UART sample found...
I have a problem with timer 3 of nrf52820.
It concerns a trailing edge dimmer implementation based on timer 3. A gpiote is used to sync the zero crossing.
I use ppi...
Dear Nordic-Team,
I designed a custom PCB using the nRF9151 as the host processor, the nRF7002 as a Wi-Fi companion, and the nPM1300 as the power management IC. The Wi-Fi...
Hello,
I encountered a strange behaviour on a nrf52832 : - I flash a a debug firmware (with debug optim in build config) : I can run debugger and add breakpoints - I stop...
I am developing an application that uses NCS2.8.0.
For FW updates, the nRF52833 USB ACM bootloader is enabled.
However, there are some problem.
My device has a battery...
Hi all hope you all are fine and doing well.
I am trying to use the Soft UART (uart-bitbang.c driver) on nRF52 DK for a low-speed UART connection. The initialization fails...
Hello, I am not sure if this is the most appropriate place to ask this question, but any comments are welcomed. I am developming a sensor platform that tries to use extended...
