Hi,
There is much talking about the "large data transfer" over BLE, the l2cap channel being the best option for the moment.
However, does anyone know the datarate achievable...
NRF24AP2 with MSp430F149 . ASYNC 9600 N 8 1
step 1 : reset NRF24AP2 with reset pin , and received a pulsing signal through RTS pin
step 2: send a char (0x4A) to NRF24AP2...
Hi guys,
I am using the gcc setup to program my boards. However for flashing the softdevice I use nrfgoStudio. SO I downloaded the hex file and fashed the siftdevice. But...
How do you create hid information for a joystick and send it over BLE. Nordic doesn't seem to have
primitives for this (they have keyboard and mouse facilities). I'm working...
I use a PCA10001 board as peripheral role of heart rate service and it can be discovered by control panel. But as I download the experimental program of central role of hrs...
I'm reading the source for the nRF Toolbox app for Android 4.3 and comparing it to the Proximity Profile spec from the Bluetooth SIG, which has this to say about path loss...
Hi,
I recently found out about the Periodic interval feature on GRTC CC[0] and it seems like it would be quite useful for my application. Most of my code so far uses the...
Hello,
I would like to ask whether nRF7002-DK allows connection in STA mode to Wi-Fi with a hidden SSID and whether it can create a softAP with a hidden SSID? If so, please...
I'm looking at the `peripheral_csc` example to understand how to implement write responses. It seems for the BT_UUID_SC_CONTROL_POINT attribute, ` bt_gatt_notify() ` is used...
Hello,
I programmed the sample peripheral_uart on an nrf52840dongle_nrf52840, working in Linux and SDK v2.5.3. I had no problems using the Programmer in nRF Connect for...
I am working with an nRF5340 device and I want to understand the maximum achievable BLE throughput for both 1M PHY and 2M PHY. Could you please provide guidance on:
...
Hello,
I see in the datasheet that the nRF54L15 has an internal 128Mhz clock.
For applications that do not utilize the BT radio on the nRF54L15, is the external crystal...
Hello all ! I'm currently trying to make a scan with our custom board, I've made a custom board with our GPIO and the use of the SPI4 instead of QSPI for the 7002 -> 5340...
I set up the wifi_shell sample using a nRF7002DK and noticed that it is leaking 104 bytes of heap after each wifi connect/disconnect cycle. This is with version 2.7.0 of the...
Hello,
I am solving a problem with nRF7002-DK, I am using TCP sockets for communication. MTU can have up to 6800 bytes, unfortunately, both in STA and AP mode, the connection...
My prj.conf:
First question / issue:
I am trying to make use of the azure dps and since I'd like to use the UUID as device id i am trying to set 'AZURE_IOT_HUB_SAMPLE_DEVICE_ID_USE_HW_ID...
I am trying to make an ndef record using t4t, but it fails.
For example I'm trying to convert the example 'record_text' to work with t4t setup, and it always fail.
Is...
Setup: nrf5340dk Zephyr: ncs 3.1.0 Hi, I am trying to enable firmware update for CPUNET over Serial (USB_CDC). I enabled update for CPUAPP and it works correctly, but not...
Hello,
I am working on a custom board based on the nRF5340 SoC . When I build any BLE sample (for example, peripheral_hr or peripheral_uart ) for the nRF5340DK , the build...
Hi, the nrf54l15 DK documentation states "nRF Connect for Desktop's Board Configurator application can be used to select if the nRF54L15 SoC interfaces with the external memory...
Hi,
I am using NC9 2.9.0 with VSCode and NRF extension.
I have seen that since version 1.2 of Device Information Service (DIS) spec , it is theorically possible to have...
