Hi,
I am using a custom pcb with a nRF51422 chip, and trying to setup ANT communication between 2 modules, but the sd_ant_channel_id_set call returns an invalid address...
Hi,
To use bidirectional continuous scanning mode in ANT, I have to transmit Extended Broadcast/Acknowledged/Burst messages using ANT Msgs 0x5D, 0x5E, and 0x5F (ANT Message...
We are preparing to get BT qualification for our product, developed with the 6 stack now, however want to update to 7 when it is finally released. A comment from the testing...
What is the best way to minimize transfer in progress errors when trying to send ANT messages? I am using the S310 stack on an nRF51422. I have a busy ANT channel that is...
I'm running into a weird timing issue with a nRF24L01+ which I'm not quite sure how to work around in the general case. The basic setup is two radios, A and B. Auto acknowledgement...
I am using mbed library to get leg up on development.
This is the first time I am writing any MCU application and it sure makes things a lot easier.
I am using nRF51822...
I've recently began experimenting with the HID service and connecting to iOS devices in order to achieve lower connection intervals with Apple products (as described in their...
Hello,
I'm having trouble saving signing keys to the KMU on the nRF54LM20-DK.
I'm using the build for the nRF54LM20B, as recommended here, so the KMU should be used for...
I am working on a project, in which we are using nRF Connect SDK v2.9.0 on a custom board with the nRF5340 SoC. The device is a BLE peripheral implementing a couple of GATT...
Hello,
I am designing a device utilizing the InvenSense ICM-42688-P 6-axis IMU. We are currently targeting two SoCs for our product line: the nRF52832 and the newer nRF54L15...
Hello,
I have a question regarding copying the generated images to a dedicated location after the build has finished.
I need to copy:
build/merged_CPUNET.hex
build...
Hello I'm going to recover firmware of dongle(nrf52820). But there isn't reset button in dongle. Because the nrf52820 is too small I think. So how can I do and which pin I...
We have a Nordic 52840 based product which today we support with a custom gateway hardware. Now we want to write mobile apps (Android and IOS) to talk to this directly.
...
Hi, we are using your nrf_cloud_fota library to download new FOTA updates from nRF Cloud, using NCS version 3.1.1.
We are also using MCUboot with the Swap using offset algorithm...
Hi
In nordic connect sdk (2.6.0) a notfication on a peripheral device is send by bt_gatt_notify_cb. The second parameter of this function (bt_gatt_notify_params) is a struct...
We obtained a Power Profiler Kit II.
I updated nrf Connect to latest version, then installed App power profiler.
The following state is reached:
When i launch the App...
Hello.
I need some advice - I'm a beginner. I tested the transition to sleep mode via __WFI for the nrf52840 Dongle (VS code, SDK v3.3.0). I need some advice - I'm a beginner...
What is the recommended termination for unused RF pins on the nRF54L15 in QFN48 (QFAA) package? Can you confirm this is acceptable?
ANT Pin 31, floating VSS_PA Pin 32, grounded...
I just realized this feature is available from NCS V3.3.0.
Does it support nRF52 series such as nRF52832 with DFU through BLE?
In this page, it seems only nRF54 are included...
Hi:
Is there a complete manual (Datasheet ) for the nRF54L15 or nRF54L series? I got the PDF for nRF54L15, nRF54L10, and nRF54L05 Wireless SoCs PRELIMINARY DATASHEET v0...
