Using S120 V 8.0.0.3 alpha, processing a BLE_GATTC_EVT_READ_RSP,
received 0x16 bytes of data but there is more to read. Next call to
sd_ble_gattc_read using the same connection...
Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
SWI*_IRQ is using by softdevice to send event to application, I want to know which priority does softdevice set for them?
Does sd_nvic_critical_region_enter() disable...
I am a started guy.
I only need a bluetooth device (BLE) to check the signal and mac address.
What is the best choice?
I need the smallest and low powered!
Thank you...
I am using nRF52840 as host processor. Now I need to connect to nRF7002 for WiFi usage. I am using ncs 2.2.2 SDK. I have a few questions? 1. Does nRF7002 work on v2.2.2? I...
I'm running into issues with programming external boards (an NRF52832_xxAA_REV2, an NRF52810_xxAA_REV2, an NRF51xxx_xxAC_REV3, and an NRF52832_xxAA_REV3) through a custom...
Hi all! I need to see the printks and log messages from the b0n and cpunet app in RTT Viewer. The problem is, whenever I connect with the SEGGER RTT Viewer to the netcore...
Dear nordic This ticket is a feature request to implement SSL max_fragment_length of 2k while initiating a TLS connection, when offloading TLS to the NRF9160 modem. As stated...
Dear Nordic,
I am debugging a custom hardware with a nRF7002 on-board, using wifi shell app. At this moment the shell does not work as expected, needs to locate where the...
We have two nRF52832-QFAA E0 version devices; Bluetooth works on one, but on the other, it used to work but stopped working over time. Even though we upload the same code...
Hi,
i am working on a project using the nRF54L15.
Hardware: custom board with nRF54L15
Software:
Wirepas SDK (1.6.2)
nrfx drivers (version 3.9.0) with some customization...
Hello
We are using nRF5340 as our EVK with a 12 antenna array plate(4x4 with center 4 ones not being there). Our beacon uses nRF52833.
We used Nordic's sample codes- ...
Hello.
I am currently migrating a project from NCS v3.2.4 to v3.3.1 and transitioning from Partition Manager to devicetree-based partitioning, following the official migration...
Hi,
I am using bare metal SDK v2.0.0 and am trying to build the fuel gauge sample inside nrf-bm\v2.0.0\nrf\samples\pmic\native\npm13xx_fuel_gauge. I am using bm_nrf54l15dk...
I am using nRF54L10 with nRF Connect SDK v3.1. The device connects over BLE, wakes every 30 minutes to read sensor data, and then should enter deep sleep (System OFF). However...
Hello, I am currently experiencing an issue with the 802154_phy_test example on the nRF54L15-DK board, and I would appreciate your technical support.
[ Environment ]
...
We are experiencing an issue with the QSPI driver on nRF54L15 where external flash access stops working after a BLE bonding procedure.
The system works correctly until bonding...
Hello
I am developpping a product with composite USB (CDC_ACM & HID) and Bluetooth Low Energy, based on a nRF52840 chip.
Can Nordic provides PID free to use for small...
