I am getting get BLE_EVT_USER_MEM_REQUEST and BLE_GAP_EVT_CONN_PARAM_UPDATE event, when writing to ble device, sample code did not handle these event, and seems no document...
Hello:
Why do I erase SDK5.2 version of flash and read not, in SDK4.2 can. I tested nrf51_sdk_v5_2_0_39364\nrf51822\Board\nrf6310\flashwrite_example is a good example.However...
before i write the flash, it has been erased.so ,its value is all 0xff.
when i write 0x00 to flash address 0x0001,the value read out is not 0x00 but 0x01,and the value in...
I'm looking for a way to use the nordic uart service ( devzone.nordicsemi.com/.../ble_sdk_app_nus_eval.html) from Linux using the native Linux BLE Stack (BlueZ). My application...
Hi,
I've created an application using the S110 experimental ANCS demo. I successfully implemented ANCS and then began to structure my application around it. At some point...
Hello,
In an ongoing company project we use a couple of nRF51 transceivers forming a beacon enabled wireless sensor network consisting of one base station and multiple...
I want to count clocks in order to implement a watch. I use the RTC0 as my time-base and count mainly with this device. As it has just 24 bits it would not last for long,...
Problem : I am following on Bluetooth Fundamental Course on Nordic Academy webpage. I successfully advertising BLE with non-connectable option. But change adv_param to BT_LE_ADV_OPT_CONN...
Hi there,
I have implemented the ability to pair the BLE peripheral in our app. However, some users may prefer to connect via IOS settings.
I have seen a thread which...
Hi ! Its me again. I'm using zephyr 3.5.0 via zmk. I'm trying to play a 60 Hz uncompressed PCM file from a wav embedded in flash memory.
I'm noticing some inconsistent output...
I had previously existing firmware that performed a firmware upgrade using mcuboot and dfu_target. This was done over bluetooth but did not use any existing available bluetooth...
Hello,
I'm trying to build my program for a custom board with FOTA BLE.
Im using v2.9.0 for the SDK and the toolchain. The custom board has a nrf52832.
When building...
In the 'nRF91 Series Antenna and RF Interface Guidelines' document there is a section ' 4.3.1 Combined GNSS and LTE antenna example' which shows a potential way to use a single...
Hi everyone,
I have an nRF9151 connected to an nRF52840/(or nRF54l15) over a single UART . I want to:
perform DFU of the nRF52840 from the nRF9151, and
also...
I am currently working with the Channel Sounding sample on the nRF54L15 DK boards (SDK and toolchain v3.1.1) and using Nordic’s multiple-antenna support as described here...
Hi,
I have a general question about the GRTC accuracy on nRF54L15.
In the manual it states the following:
We will like to use the GRTC as timekeeper with an external...
HI all,
I'm working on a firmware for the nRF9151. In the development desk all works good. But under release conditions the software crashes cause of locked RAM access...
After using the official example hci_uart with the nRF54L15-DK, it is configured as an HCI controller. I used bluetoothctl commands like scan on and connect to scan for peripheral...
I'm leveraging a fuel_gauge example to pass a version string as part of a Device Information Service. When viewed in Nrf Connect (desktop or mobile) only the first character...
Hi,
I tried to build and flash the binary of NRF WiFi Course Example L2 E3.
There was no build and flash error. But there is no logs on both UART terminal.
My setup...
Hi Nordic Support Team, I'm experiencing severe memory constraints with the AWS Io T Core example on the nRF 7002DK (nRF 5340) that make it impract ical for real-world applications...
Hi, we are using the nrf_cloud_fota_poll library with CoAP to interface the nRF Cloud for FOTA updates for nrf9160.
In lossy mobile network with bad reception, the FOTA...
