I have a working project where pin 16 is configured as a low-level interrupt source.
it is working well with SDK 15.3
after porting to SDK 17.0.2, it is not triggering...
Hello Nordic Support Engineers and fellow developers ...
Just a note to thank everyone for help via this forum. I started very inexperienced with Nordic SDK a year ago and...
Hi,
I recently purchased a thingy91 for a project. I'm trying to follow instructions from a Nordic youtube video ( https://www.youtube.com/watch?reload=9&v=xQ7hDzRULJQ ...
I have a nRF5340PDK, Now I want to know the lowest power consumption of this chip in different condition, such as adv, connect, sleep. But I am not sure how to config the...
Hi, i am using:
-nRF 52 DK
-nRF 52832
-Sensor of Maxim Integrated
-SDK 17.0.2
I have some problems in handling the I2C through the nrfx module.
This is my ReadByte...
Hi, I have a set up consing of an nrf52840, a Raspberry pi and a Linux workstation, which communicate over IPSP following the IPSP sample from Zephyr OS. The nrf52840 is a...
In section 5 of 'nRF91 Series Antenna and RF Interface Guidelines' there are a couple of circuit diagrams relating to antenna tuners, could you please provide details of how...
Hi,
I just saw the announcement for PRS support. This is very interesting to us for use cases where GNSS reception is temporarily poor. Questions:
What do we need to...
Hi Support Team
Must inductors be placed between the SW1/SW2 pins and the VOUT1/VOUT2 pins of the nPM1304? Can VOUT1/2 output normally if removed the inductors? Many thanks...
Hi,
I am working on a BLE application using the nRF5340 SoC(custom board) and Zephyr RTOS (NCS SDK version v2.9.0)
When I call bt_enable(bt_ready_cb_t cb) , Bluetooth...
Greetings, all. I'm a rank beginner here with all things Nordic but almost 50 years of embedded experience with other devices, environments, etc. I'm trying to develop for...
Custom device using nrf5340, with NFC card emulation functionality.
To use the NFC, I understand that I should use the supplied nfc_t4t library (binary) and its api. I have...
Hello, I'm developing on an application which requires to catch high speed, variable size and bursty (~0.5 Mbit/s) data from a sensor connected to a nRF9161DK trough a UART...
I'd like to use the DeviceTree Visual Editor to create the DTS for a custom board starting with only the bare device. But it seems for some reason that the DeviceTree Visual...
Hello,
I’m using the Thingy91X board (nRF5340). For my application, I need to run BLE and Wi-Fi simultaneously, so I have to increase the application size. To do this, I...
Hi I'm trying to work on OTA implementation for zigbee with nrf52840-DK boards.
there is a sample available in ncs2.9.0,light switch,but i understand it can only work as...
Hello,
I have some issues to do function an ntc thermistor with a nrf54L15DK.
An error about a wrong configuration of the adc reference or or the ADC gain appears almost...
Hi,
I have some problem when scan advertising packet using nrf52840dk with ncs v2.5.0.
when I scan during 30s in the same position, I got a list rssi value same that...
Hi Team,
Hello Team,
I'm currently working on integrating the Sensirion STS40-CD1B-R3 temperature sensor into the peripheral_ht . To do this, I pulled the STS40 driver...
When I used the CS instance for distance measurement, I wanted to set multiple initiators. Therefore, I configured BT_CTLR_SDC_CS_COUNT to 3. However, I didn't know where...
