I have an NRF9160 system running and I see mention of " The nRF9160 PWM peripheral can capture the period and pulse width of an external PWM signal" but was a little confused...
Hello, I am encountering an issue while setting up an OpenThread Border Router (OTBR) using the following hardware: nRF52833 board (flashed with RCP firmware) nRF52840 board...
Hi
custom board using the nRF9160, toolchain version v2.6.0, mfw_v1.3.6.
Sorry I can't provide a decrypted modem trace, but I hope the screenshots are enough to show what...
Hi, I am working with nRF52 DK (52832), and the issue I am facing is that i am unable to increase the data size of data SPI -DMA can receive. Currently it is configured at...
Hello everyone,
I want to evaluate the power consumption in idle mode of the nrf9151 sip.
Environement:
nrf9151dk_rf9151_ns
nRF Connect SDK Toolchain v3.0.2
VScode...
I’m using SMP over UART to send the erase command ( {"slot": 1} ), and it only erases the application core image (image 0). I also have a network core image (image 1) present...
So i am currently referring this ticket and from that I get to know that when when setting parameters for create config (HCI_LE_CS_Create_Config) command for channel sounding...
How can I relocate or manage the transition between the bootloaders interrupt vector map and the applications interrupt vector map which will be at different addresses in...
Hi !
I'm completely new into programming this device.
I downloaded the nAn-36 source from Github and I'm trying to make it work on a PC10000 dongle.
The code stops in the...
Hi,
I wonder if there is any way to disable the Rx FIFO so that I don't have to fill it to generate an event, since I need exact timing for every incoming byte.
Also,...
Hi, I am trying to connect N51422 server to anther vendor's client... the devices always disconnect after 30 seconds of connection.
I found that the reason of the disconnection...
I have seen this question asked on this forum in several ways but none of the parameters match up to my specific case. I am getting this error when I try to run the example...
Hi,
I load the s110 softdevice (I tried many versions 5, 6 and 7)
When I load my app on the SOC using Keil and the nrf_xxaa_s110 (256) target, the app doesn't run.
I'm...
Dear Nordic Developer Zone,
I have implemented a real-time-clock using application timer which is based on the on-chip real-time counter on NRF51822.
A concern of mine...
I'm trying to get the Nan-36 example working on my PC10001 board and I'm having some trouble. I've tried using both SD110 version 6 and 7 with appropriate (I think) memory...
Hi,
Is there any connection/disconnection API in ant+ (sd210) similar to BLE?
I want to use this to control the device activity cycle, if I get disconnection event, would...
Hi,
I'm trying to implement a specific communication protocol using the SPI on a nRF51822. The SPI on nordic side will act as slave. When CSN line goes low, I will also need...
Hi,
I currently have a problem with the continous scanning mode. I implemented the scanning mode that my device searches for the first 4 seconds after power up then picks...
Which example projects are compatible with s110 v7 for nRF51822?
I keep running into samples requiring "Legacy Keil" to be installed.
I just want a clean s110 v7 example...
Uint32_t data using sd_flash_write written many times to the same address, you must perform sd_flash_page_erase before writing it?
(English is not good, with Google Translate...
Is the DC/DC converter enabled when running ble_app_beacon?
Or is it only the LDO that is enabled?
I am running the application on nRF51822-DK.
BR Magnus
Hi,
I happily use the JLINK UART interface which show up as COMxx on windows for both the PCA10000 and PCA10001.
We are trying to 'see' the same on Linux. Have inatlled...
