hi........... folks
i am merging two programs together uart and TWI sensor ...using nrf52382 and segger 15.2version
i am getting the error in ble_nus_send ,
even i have...
Software and Softdevice: SDK 12.3.0 keil5
Platform: Windows 10
Hardware: NRF52832 DK
I am trying to combine WDT and FATfs together. But once I have both of them, there...
I am trying to get a good handle on the difference in average power consumption between BLE point to point and Zigbee on an nRF52840. We have battery powered products and...
Hi, For my project, I need to design a BLE packet sniffer which scanning the 40 channels. Therefore, I need 40 dongles are connected to a computer that can read and transfer...
I am writing code to get a nrf52840 DK to associate with an existing 802.15.4 coordinator using the 802.15.4 API module within SDK 15.2.
I've called "mlme_scan_req" and...
Currently, I am able to use Mqtt Publisher or Subscriber with only one Nrf52 device. I can ping to the device with link-local address.
I am using Nrf52832 with SoftDevice...
Hi everyone,
After days of figuring out how CMake works, I try to write a CMakeList.txt myself, and decide to put my progress on this community. Right now, using CLion with...
Hi,
just got my PPK2 and noticed some strange behavior:
the only thing connected is USB data/power, no DUT. Power output is off. If you start logging it displays some...
Hi,
How to implement two sets of SPI on the NCS v3.0.0 nRF54L15 P2 port? If it can be achieved, please provide the corresponding IO ports for these two sets of SPI.
Kind...
Hi，
We are designing a cellular antenna based on the Thingy91x reference, which needs to support all frequency bands of the nRF9151 cellular module. The antenna tuning switch...
Hi Nordic team,
I am using nRF54LM20DK with NCS v3.3.0 and trying to enable QSPI.
However, there is no &qspi or &qspi20 node in DTS, and adding it causes build errors...
Hi Nordic team,
We are designing a custom board using an nRF54L15 together with an nRF7002 WLCSP.
Our board has a single 3.3 V power rail. We would like to confirm the...
Hi,
AI says this is a known issue, but I want a much stronger explanation of why this scenario breaks. I run the server program on the nRF52840. I understand that it is...
Hello!
I am stress-testing the nRF54L15 devkit by sending it random-sized chunks of data over UART at 921600 baud, which the devkit code receives using the asynchronous...
In the absence of a QGAA reference, is there anything to be aware of when designing a QGAA board?
For example, with the nRF52840, the WLCSP and QFN references used different...
Hi Nordic team,
I am working on nRF5340 and trying to enable MCUboot serial recovery DFU in single-slot mode with both signing and encrypted images.
Environment: 1. SoC...
Summary
The Zephyr RRAM driver drivers/flash/soc_flash_nrf_rram.c does not pass NS-side reads of TF-M secure flash through soc_secure_mem_read when the device tree uses...
I am interfacing a TLV320AIC3204 codec EVM with an nRF54L15 board using I2S.
The codec EVM default configuration is working correctly. I verified audio on the EVM side....
Bluetooth physical layer Direct Test Mode testing is used to verify BLE low-level RF transceiver performance. The required software is nRF Connect for Desktop V3.7 + Direct...
Hi,
When starting nRF Connect for VS Code, SDK v3.3.0, the message Unable to resolve configuration with compilerPath: "C:\ncs\toolchains\fd21892d0f\opt\zephyr-sdk\arm-zephyr...
Hi,
We have two option to use Flash memory,
Option 1: We are planning to use Flash Memory on the SPI bus shared with the NRF7002. Kindly confirm whether this configuration...
