hello,
I use nrf51822 + S130 + SDK12.2 in my product, nrf51822 work at central + peripheral mode，and i use nrf_duf_flash module for my dfu funtion.
The problem is, i...
I want to communicate Central and peripheral devices with KeyPass. Also I want to generate keypass in Peripheral device. But keypass should to include symbols, low/upper case...
I am using SEGGER Studio on MacOSx.
When use the latest mesh SDK, I can run the light_control example and see the debug log in the Debug Terminal of SEGGER Studio.
However...
Hello,
I'm trying to setup a nRF Cloud Bluetooth gateway using my PC (with openSuse 42.2 64bits and rRF Connect v2.1.0 + nRF Cloud Gateway v0.9.7) and a nRF52 DK and I...
Hello: I am using an NRF51 dongle. Date on the device sticker on the back is 2015.38. Also using nrf51_ble_driver_linux_0.5.0.
I can see/connect to the device I am trying...
Hey,
I just want to know if anybody sucessfully connected HDMI CEC (One-Wire bus) with the nRF52832.
I would be very grateful if anybody could share the library or give...
Hello,
I am evalating the nRF9151-SMA-DK with a Monogoto SIM card that uses Skylo NTN connectivity.
I am able to reach the internet, since DNS resolution works:
...
Hello,
We are using a custom board based on the nRF5340 + nRF7003 Fanstel module with NCS SDK v2.6.2.
Our application uses MCUboot with dual-bank OTA updates. The secondary...
Hi,
What file or files should contain CONFIG_GPIO=y for a simple application developed with nRF Connect SDK v2.9.0 such that VS Code does not show squiggles under #include...
Hi,
BLE throughput differs between NCS v2.6.0 and v2.9.2. v2.9.2 appears to have fewer MoreData packets. (Both have CONFIG_BT_CTLR_SDC_MAX_CONN_EVENT_LEN_DEFAULT set to...
Hi, Team:
I want to make an LED blink during OTA upgrade and stop blinking after upgrade.
How do I configure prj.conf, sysbuild.conf, or provide some demos
Thank you...
Hi
I'm encountering a problem than the ANT device cannot be scanned. you can use project "ble_ant_app_hrm_v324"(ncs 324）, and modify "
light_rx_open_head" to connect...
I have discovered a serious issue with Bluetooth connectivity on iOS 26.
My device use nrf52832 and sdk15.3, it consistently disconnects just a few seconds after a successful...
Hello everyone,
I have tried several different approaches to solve this issue, but I have not been successful so far.
My goal is to generate an interrupt when the LIS2MDL...
Hi,
We have sent out our product (includes the nRF9160 SiP and an nRF52840) for EMC testing and the test lab is asking for the following:
nRF9160 LTE Cat M1 and NB...
We have noticed an issue with our device built on nRF5 SDK + nRF52832 when connected to iOS 26.
Initially after connection, everything is ok. Then we attempt a connection...
As part of the Bluetooth LE course we need to setup and install the nRF BLE sniffer for wireshark. I have followed the explained steps in the course to set up wireshark to...
Hello Nordic Team,
I am designing a custom PCB using the nRF52840 and a PCB trace antenna for 2.4 GHz BLE.
In my current design:
I will take nRF52840 dongle antenna...
I am using the nRF5 SDK, nRF52833, and nRF52832.
I flashed the following two demos:
nRF5_SDK_17.1.0_ddde560\examples\ble_central\ble_app_uart_c\pca10100\s122 (nRF52833...
Hello,
We are currently developing a Zigbee product using nRF Connect SDK v2.8.0 . While reviewing the release notes for NCS v2.9.0 , we noticed two critical bug fixes related...
