I use example from SDK 13 ble_app_uart_c.
I changed uuid to my uuid from nrf51 peripherial device. I get event BLE_GAP_EVT_CONNECTED
where made
err_code = ble_db_discovery_start...
dear all,
i need your help.
Where we are:
We use mbed software developer platform.
We have BLE Nano V1.5 + MK20 USB Board V1.0 from RedBear.
We are able to generate...
Hi:
environment:
target board: DK52 board and run LWM2M example of IOT-SDK v0.9
router: ubuntu 16.04 on VM and runs bsserver and LWM2M server on ubuntu 16.04 ...
Hi,
I'm interfacing a nrf51822 and a H8/3294. My question is how much can I drain a the txd pin of the H8/3294. That means my question isn't really about nrf51822.
In documentation...
Hi,
On the 3.30 of nRF52832_Rev_1_Errata_v1.5.pdf, the sleep current with LFXO active is 0.5μA higher.
I am using a nRF52832 module with the low frequency crystal oscillator...
Hi,
I'm using nRF52832 on SDK V12.2. I add the connection params in the conn_params_init:
static void conn_params_init(void){
uint32_t err_code;
ble_conn_params_init_t...
Dear Support Team,
I'm currently using the Asset Tracker example : https://github.com/nrfconnect/Asset-Tracker-Template and would like to enable at the same time the support...
hello,I am developing an ESL system using SDK v2.8, but I have encountered some issues ，The chip I am using is the nRF5340；So，Which version is suitable for developing ELS...
Hello
I am new to nrf9151 development. I cannot find the binary of the nrf_modem library for nrf9151.
I have downloaded the sdk_nrfxlib-v3.2.1 - Under nrf_modem/lib/cellular...
nRF Connect SDK 3.0.2
Insight SiP ISP2454 module
Using zephyr
mcu boot.
In my application, I am using a 400 ms timer to measure the battery voltage. However, when...
We have a production issue where about half of our units have odd inconsistent behavior. Failures vary from board-to-board - DFU failure, BLE connection issues, partial initialization...
Can somebody please confirm whether the following piece of code will use a 32-byte encryption key stored in KMU slot #4? I've successfully tested encryption/decryption using...
Hello,
There are many questions out there on correctly determining the SAADC pin input voltage limits. The equations given in the product spec is very straight forward:...
Hi, I am working on a project that utilizes the nRF52832. How to properly enable Access Port protection in the code, if I want to have a single firmware for all three revisions...
Hi,
I was using the Direct Test mode app from the nRF desktop to try to run a DTM Tx Test on nRF54L15-DK. The app could find the device (but there're two serial ports xxx51...
Hello,
I am currently working on a project using the nRF54 Series and I am evaluating the capabilities of the CRACEN versus the nrf_oberon software library.
I would like...
Hi,
I am wondering why can't CODED PHY and BLE Audio be modded into the nRF52832. Are there any hardware requirements for both to be supported ? If so, is there any info...
I observed that I can't flash my board in VS Code when a USB-serial adapter is connected to my computer. When the adapter is unplugged everything works.
The interesing...
nRF54L15 + NCS 3.02 + Toolchain 3.02
So I have followed Dev Acadamy exercises for Serial Recovery and BLE FOTA. In my project I now have MCUBOOT for Serial Recovery but...
Hi, we are writing the register TASKENTERSHIPMODE to enter ship mode, and everything works ok. But as the ref manual says, when VBUS is present this task is ignored.
Is...
