Hi,
We are using the nrfconnect for thread and zigbee 3.2.
We have modelled our Bluetooth peripheral, running on the nrf52840, on the BLE UART example. It connects fine...
I have installed nrf-command-line-tools_10.24.2_amd64 and jLink_Linux_V794e_x86_64 on Ubuntu 22.04. I have also installed nrfconnect-5.0.2-x86_64 for desktop and the Toolchain...
Hello,
We have an NCS v2.2.0 nRF5340 application with MCUboot that requires GPIO control of a few pins extremely early in the startup process. We have a signal "A" pulled...
Sorry if this is too off topic, I actually don't have any problem with my nrf52840 dongle, but the App I'm communicating with. But maybe someone of you has run into the same...
We are using an MCU that pushes data packets to the nRF9151 communication module via UART. According to our module service provider, each data packet can only be up to 2 KB...
I am testing PAwR interoperability between:
TX side : third-party chipset acting as PAwR Advertiser/Transmitter
RX side : Nordic board running nRF Connect SDK...
Goal: "I am trying to get SPI3 working with a custom MAX30003 driver in a sysbuild non-secure ( _ns ) application, based on the peripheral_uart example."
Problem: "The...
Hi,
I have been evaluating the use of nrf9151 using two development kit boards.
On my first board, I set it up initially using quick start under the nRF connect app...
Hi,
The SDK version I am using is 2.6.1 and the example is "matter lock".
I wrote the following configuration into \child_image\mcuboot\prj.conf.
And add the code...
Hello, I encountered a problem while using the nrf5 SDK. In my software, I used a UART for debugging data output, a libuarte library for command output, and an app_button...
I'm trying to use nrfutil as part of a script that sets up the toolchain environment automatically using direnv .
For example:
I'd like to know how the bundle ID can...
As subject, NCS 3.0.2, I use demo 'peripheral_power_profiling' to test current on NRF52832 DK board, but the demo cound not run when power on, There is no log output, and...
Hello,
I am exploring power management on the nRF54L15 DK with nRF Connect SDK v2.8.0 (Zephyr v3.7.99) .
My goal is to:
Enter deep sleep / system off mode.
...
I am trying to wake up the NRF54L15-DK from deep sleep using RTC. The device goes into deep sleep but never wakes up. I would like to know if RTC can wake up the micro from...
Hello,
I am trying to run the wifi_scan example but I am getting a BUS FAULT error as seen below. The SDK is v3.1.0, and the SDK Toolchain is also v3.1.0.
1. Going...
i have version 0.9.2 of the nRF54L DK....
i've noticed there is now 1.0.0 documentation....
have there been any HW changes -- use of "production" MCUs, etc....
more...
Hi Team,
We are looking into the new Thingy 91 X and were wondering if it will be able to run the nRF91 Pizza Demo .
I understand the demo was originally created for the...
Hello,
I'm working on Windows 11, with the nRF Connect for VS Code v2025.5.512 extension, with ncs v3.0.2. I'm using the nRF54L15-dk (PCA10156; 0.9.2; 2025.7) development...
citing the following issues
I've been able to implement the 16 Mhz on the SPIM3. However, the incoming data on the MISO is still corrupted. With my oscilloscope I can...
