I am working on a project using a ble nano (nrf51822) using the Nordic SDK 8.1. In the examples I found a way to control an LED using the methods LEDS_ON and LEDS_OFF. I wanted...
Hello,
I am using ble_app_gls example and I have implemented static passkey in the code. Now I want to see if wireshark shows the passkey when I connect to ble devices. For...
Hi Team,
We are implementing an UART communication between a M4 processor (UART master) and a nRF51 (UART slave) and we want to use the UART in Low Power mode with flow...
Hello everybody,
for my project, i will bond the peripherial with the central.
I test my device with the MCP and can connect without problems. When i press the Bond Button...
Hi all,
I am trying to count the positive edges of a 3.5MHz signal with GPIOTE, PPI and the TIMER1. Unfortunately i can only measure to frequencies up to a little more...
Loaded Softdevice S140, ( Using NRF52840 DK board ) using NRFgo Studio.
App flash base is set to 0x00021000 and app RAM base is set to 0x20003000
Looking at the CPU...
In our earlier projects with nRF51 and SDK 8 we used to have bluetooth device names of length 13 or 14 characters. However, when using nRF52 and SDK 12 I noticed that the...
Hi,
I'm not able to flash nRF54 DK. Log as below:
2025-08-29T06:47:39.828Z INFO Initialising the bundled nrfutil device 2025-08-29T06:47:39.874Z DEBUG Started watching...
*Note that this is only an issue when the central and peripheral are simultaneously active.
This is my current setup for starting advertising, but it requires a deprecated...
Intro We are using the nRF9160 with sensors we manufacture. The code developed is based on the serial SLM sample, toolchain v1.6.0. I am trying to keep the code/project files...
Hello. I have an issue with my development board. When attempting to recover the board, i cannot due to access port protection. This is the specific error message from the...
I'm new to developing nRF devices. This is the first time to set up SDK.
I installed Toolchain Manager v1.2.6 to install SDK, but it is too slow and falls into error. It...
am trying to mount little fs example with my external flash winbond w25q256 but my nrf52840 board taking internal memory and am using qspi
it get automount and writing in...
Hi Nordic,
I need to build an Auracast broadcast speaker (LE Audio BIS broadcaster). Besides audio, I also need two-way data exchange between the Auracast source and the...
Hello,
I am trying to have my own BLE advertising and scanning (with filtering) custom service (from now on peer service) in parallel with BLE mesh. So far I've been able...
Dear Nordic Team,
I have to use PSA Crypto key derivation in my NRF54L15 firmware during BLE communication with BLE Central, however, I am experiencing a problem when I...
In the function mentioned above, I repeatedly perform the following operations in a loop at a specified interval:
Power on the internet module
Connect to Wi-Fi...
I am trying to program modem keys using pylink and Modem_Shell with RTT enabled and it is almost working.
I find that the maximum download size for a command that I send...
Hi,
I got strange behavior of the SPI4 nrfx driver on nRF5340 (using nRF SDK v2.6.1 non-secure build with BLE enabled on NET core). Namely, every time I try to receive bytes...
Hello DevZone,
Our team has been working on a customized firmware solution that has been flashed onto the nRF52840 Dongle to meet specific requirements.
Usually, DK is...
In pm_handler_secure_on_connection, I see that it only looks for BLE_GAP_EVT_CONNECTED events if PM_HANDLER_SEC_DELAY_MS is not in use. I also see the comment "In normal circumstances...
The power domains for the nRF70002 aren't very clearly documented in the product specifications, so we're not entirely clear on how we should be connecting the VBAT pin. ...
